http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
옥내소화전 방수구에 부착되는 감압오리피스의 감압성능에 관한 연구
박봉래,이맹로,장경남,백은선 한국화재소방학회 2015 한국화재소방학회논문지 Vol.29 No.3
Indoor hydrant facilities are used to fight initial fires before more intense fire extinguishing activities. Fire extinguishingfacilities should ensure good fire extinguishing performance and the safety of users. Indoor hydrant facilities aremostly installed in buildings and facilities, and users must manipulate valves, hoses, and nozzles manually. When the dischargepressure is higher than 0.70 MPa, there is a high possibility that problems with manipulation and hose breakdowncan occur. To prevent these problems, a method to attach orifice-type decompression valves to the angle valves of indoorhydrant discharge outlets has frequently been used for decompression methods. However, the decompression performancewas reduced due to structural problems of the decompression valves over time. Accordingly, based on three-stageinitial pressures, applicable pressure ranges were selected by measuring the decompression performance according to thediameter of the decompression orifices. Based on the data, stable decompression valve models are proposed. These modelshave the lowest decrease in decompression performance, regardless of time. 소화설비는 초기소화를 목적으로 설치하여 소방대의 본격소화활동이전에 사용하는 소방설비로서 소화성능은 물론 사용자의 안전을 보장하여야 한다. 옥내소화전설비의 경우 건축물에 많이 설치된 소화설비로서 화재 시 사용자가 밸브조작및 호스와 노즐을 수동으로 사용해야하는 설비이다. 따라서 방수압력이 0.70 MPa보다 높은 경우 조작과 호스파손 등의문제가 발생할 수 있다. 이를 방지하기위해 사용되는 감압방식 중 옥내소화전방수구인 앵글밸브에 오리피스형태인 감압밸브를 부착하는 방식을 많이 사용하고 있다. 하지만 감압밸브는 구조적인 문제로 인하여 사용기간의 경과에 따라 감압성능이 저하되는 것을 확인하였다. 이에 따라 3단계의 초기압력을 기준으로 감압오리피스의 직경별 감압성능을 측정하여 적용 가능한 압력범위를 선정하고 이를 자료로 시간경과에도 감압성능의 저하를 최소화 하는 안정적인 감압밸브 모델을 제시하였다.
노즐 구경에 따른 포 수용액의 압력과 유량 및 농도 변화에 관한 실험적 연구
장경남(Jang, Kyung-Nam),이맹로(Lee, Maing-Ro),박봉래(Park, Bong-Rae),윤기조(Yun, Ki-Jo),백은선(Baek, Eun-Sun) 한국화재소방학회 2015 한국화재소방학회논문지 Vol.29 No.2
본 연구는 소방펌프차에서 사용 중인 라인프로포셔너 방식의 포 소화설비에 대하여 노즐의 구경변화에 따른 포 수용액의 압력, 유량 및 농도의 변화에 대한 실험적 연구로 실험 데이터를 이론적 계산을 수행함으로써 포 소화약제 성능인증기준에 적합한 폼 흡입 노즐의 흡입측 압력 및 폼 흡입 니플의 구경 모델을 제시하고자 한다. 실험 장치는 소방방재청 고시 제2012-81호 제8조(기능시험) 규정을 바탕으로 실험 장치를 구성하였으며, 포 소화약제는 수성막포 3%를 사용하였고, 혼합장치는 현재 소방관서에서 사용 중인 폼 픽업식 라인프로포셔너 혼합장치 구경 40 mm를 사용하였다. 본 연구를 통하여 라인프로포셔너 혼합장치의 인입측 압력 변화 및 폼 흡입 니플 구경의 변화에 대하여 폼 흡입 노즐의 구경이 4 mm일 때 노즐 흡입측 압력은 0.25~0.35MPa 범위 내에서 이론적 포 소화약제 성능 인증 기준에 적합함을 증명할 수 있었다. 또한 폼 흡입 노즐의 구경이 5 mm일 때는 폼 흡입 노즐의 구경이 4 mm일 때 보다 높은 압력 0.45~0.60 MPa 범위 내에서 포 소화약제 성능 인증기준에 적합한 것으로 나타났다. The purpose of this study is to suggest the reasonable model of the caliber in suction nozzle, the pressure of suction nozzle, and the flow rate about foam system of line proportioner type using in the pumpcar. To test this, the experimental study was accomplished on the ground of the standards for the Performance Certification and Product Inspection of Foam Fire-extinguishing Chemical Mixing Machine. Aqueous Film Forming Foam in 3% and pipe type air foam nozzle with line proportioner FE 40 type were used. Test result showed that the pressure of suction nozzle within the limits between 0.25 MPa and 0.35 MPa was appropriate when the caliber in suction nozzle is 4 mm. Also, the pressure of suction nozzle within the limits between 0.45 MPa and 0.60 MPa was appropriate in the higher pressure than 4 mm when the caliber in suction nozzle is 5 mm.