확률모델 불확실성을 고려한 구조물의 신뢰도 기반 최적설계 - 제2편: 강인 성능 평가

옥승용,박원석 한국안전학회 2012 한국안전학회지 Vol.26 No.6

This paper, being the second in a two-part series, presents the robust performance of the proposed design method which can enhance a reliability-based design optimization(RBDO) under the uncertainties of probabilistic models. The robust performances of the solutions obtained by the proposed method, described in the Part 1, are investigated through the parametric studies. A 10-bar truss example is considered, and the uncertain parameters include the number of data observed, and the variations of applied loadings and allowable stresses. The numerical results show that the proposed method can produce a consistent result despite of the large variations in the parameters. Especially,even with the relatively small data set, the analysis results show that the exact probabilistic model can be successfully predicted with optimized design sections. This consistency of estimating appropriate probability model is also observed in the case of the variations of other parameters, which verifies the robustness of the proposed method

선형 점성 감쇠기가 장착된 인접구조물의 진동제어를 위한 유전자 알고리즘 기반 최적설계

옥승용,김동석,고현무,박관순 한국지진공학회 2007 한국지진공학회논문집 Vol.11 No.1

이 연구에서는 인접한 두 빌딩의 진동제어를 위한 방법으로 선형 점성 감쇠기의 위치별 용량의 최적설계방법을 제시하고자 한다. 기존 연구들에서는 감쇠기의 균등분포 또는 층별 감쇠비의 민감도에 비례하는 분포의 가정 하에서의 준최적(suboptimal) 설계문제를 다룬 반면, 이 연구에서는 감쇠기의 위치별 용량을 독립적인 설계인자로 고려함으로써 전역 최적해를 결정하는 최적화기법을 다루었다. 이를 위하여 넓은 영역에서 다수의 설계변수를 효율적으로 검색할 수 있는 유전자 알고리즘(genetic algorithm)을 도입하였으며, 제어 성능 및 감쇠용량에 대한 목적함수의 정의를 달리함으로써 얻어지는 여러 최적설계 결과를 상호 비교하여 보다 최적의 해를 구할 수 있는 목적함수를 정립하였다. 기존 연구결과와의 제어성능 및 감쇠용량의 비교를 통하여 제시하는 방법의 효율성을 검증하였다. 아울러 서로 상이한 주파수 성분을 띄는 실제 역사지진에 대한 시간이력해석을 통하여 제시하는 방법이 인접 구조물의 효과적인 제진설계방법이 될 수 있음을 입증하였다. This paper proposes an optimal design method of distribution and capacities of linear viscous dampers for vibration control of two adjacent buildings. The previous researches have dealt with suboptimal design problem under the assumption that linear viscous dampers are distributed uniformly or proportionally to the sensitivity of the modal damping ratio according to floors, whereas this study deals with global optimization problem in which the damping capacities of each floor are independently selected as design parameters. For this purpose, genetic algorithm to effectively search multiple design variables in large searching domains is adopted and objective function leading to the global optimal solutions is established through the comparison of several optimal design values obtained from different objective functions with control performance and damping capacity. The effectiveness of the proposed method is investigated by comparing the control performance and total damping capacity designed by the proposed method with those of the previous method. In addition, the time history analyses are performed by using three historical earthquakes with different frequency contents, and the simulation results demonstrate that the proposed method is an effective seismic design method for the vibration control of the adjacent structures.

목표신뢰성을 만족하는 구조물-감쇠기 복합시스템의 다목적 통합최적설계

옥승용,박관순,송준호,고현무 한국지진공학회 2008 한국지진공학회논문집 Vol.12 No.2

이 논문에서는 구조물의 내진성능 향상을 위한 방법으로서 구조부재 및 수동형 감쇠기의 통합최적설계기법을 제시한다. 이는 구조부재 및 감쇠기의 최적배치를 다루는 최적화기법이다. 통합시스템의 최적설계를 위하여 다목적최적화기법을 도입하고, 이를 보다 효율적으로 다루기 위하여 목표신뢰성 제한조건을 갖는 다목적최적화문제로 재구성하였다. 수치해석 예제를 통하여 다양한Pareto 최적해를 제시하였으며, 이들이 기존 설계방법에 상응하는 순차적 설계방법 및 가중합방법에 따른 단일목적함수 최적화방법을 포괄함을 검증하였다. 여러 Pareto 최적해로부터 강성 및 감쇠장치의 사용량을 달리하는 3가지 대표설계안을 선택하고 이들의 내진성능을 다양한 지진하중에 대하여 비교 분석하였다. 이로부터 제시하는 방법이 구조물의 내진성능 향상을 위한 설계방법으로서 효율적으로 적용될 수 있을 것으로 기대된다. This paper presents an integrated optimal design technique of a hybrid structure-damper system for improving the seismic performance of the structure. The proposed technique corresponds to the optimal distribution of the stiffness and dampers. The multi-objective optimization technique is introduced to deal with the optimal design problem of the hybrid system, which is reformulated into the multi-objective optimization problem with a constraint of target reliability in an efficient manner. An illustrative example shows that the proposed technique can provide a set of Pareto optimal solutions embracing the solutions obtained by the conventional sequential design method and single-objective optimization method based on weighted summation scheme. Based on the stiffness and damping capacities, three representative designs are selected among the Pareto optimal solutions and their seismic performances are investigated through the parametric studies on the dynamic characteristics of the seismic events. The comparative results demonstrate that the proposed approach can be efficiently applied to the optimal design problem for improving the seismic performance of the structure.

이동열차하중에 대한 강합성형 고속철도교의 진동제어

옥승용,고현무,하동호,조근희 대한토목학회 2000 대한토목학회 학술발표회 논문집 Vol.2000 No.1

Optimal Performance Design of Bi-Tuned Mass Damper Systems Using

옥승용,송준호,박관순 대한토목학회 2008 KSCE JOURNAL OF CIVIL ENGINEERING Vol.12 No.5

This paper proposes a multi-objective optimization based design methodology of bi-Tuned Mass Damper (TMD) systems to guarantee robust seismic performance of building structures against off-tunings between norminal and actual conditions of the structure. The proposed approach first introduces two performance measures for bi-TMD systems, i.e., 뱊ominal?and 뱑obust?performance indices, which are defined in terms of the maximum frequency responses of the damped structure in its original design condition and those in perturbed conditions, respectively. These performance measures are incorporated into a vector form of objective functions for a multi-objective optimization of bi-TMD designs. This approach systematically finds a set of Pareto optimal solutions which are mutually conflicting in terms of the two objective functions. A reasonable design is then selected from the Pareto-optimal surface. Illustrative examples are presented for optimlal design problems of TMD and bi-TMD. The nominal and robust performances of the optimal designs are examined through a parametric study on uncertain characteristics of ground motions. The comparative results demonstrate that the proposed optimal design approach guarantees effective and robust performance of bi-TMD systems in controlling the responses of the building structures under seismic excitations.

퍼지관리제어기법의 강인성능평가

옥승용,박관순,고현무,Ok, Seung-Yong,Park, Kwan-Soon,Koh, Hyun-Moo 한국지진공학회 2005 한국지진공학회논문집 Vol.9 No.5

Using the variable control gain scheme on the basis of fuzzy-based decision-making process, Fuzzy supervisory control (FSC) technique exhibits better control performance than linear control technique with one static control gain. This paper demonstrates the effectiveness of the FSC technique by evaluating the robust performance of the FSC technique under the presence of uncertainties in the models and the excitations. Robust performance of the FSC system is compared with that of optimally designed LQG control system for the benchmark cable-stayed bridge presented by Dyke et al. Parameter studies on the robust performance evaluation are carried out by varying the stiffness of the bridge model as well as the magnitudes of several earthquakes with different frequency contents. From the comparative study of two control systems, FSC system shows the enhanced control performance against various magnitudes of several earthquakes while maintaining lower level of power required for controlling the bridge response. Especially, FSC system clearly guarantees the improved robust performance of the control system with stable reduction effects on the seismic responses and slight increases in total power and stroke for the control system, while LQG control system exhibits poor robust performance.

사장교의 지진응답제어를 위한 준능동 MR 감쇠기의 퍼지제어

옥승용,김동석,고현무,박관순 한국지진공학회 2005 한국지진공학회논문집 Vol.9 No.6

사장교의 효과적 지진응답제어를 위하여 MR 감쇠기를 이용한 준능동 퍼지 제어기법을 제시하였다. 제시하는 방법은 MR 감쇠기의 응답정보만을 이용한 퍼지추론 과정을 통하여 준능동 제어를 수행하는 방법으로서, 능동제어이론에 기반한 기존 준능동 제어기법과 달리, 별도의 능동제어기를 설계할 필요가 없는 간단한 구조로서 구성될 수 있다. 제시한 제어기법의 제어성능을 평가하기 위해 사장교 벤치마크 문제에 적용하였으며 기존 준능동 제어기법들과의 성능비교를 통하여 그 효율성을 평가하였다. 제어성능을 비교한 결과, 제시하는 준능동 퍼지 제어기법은 주탑의 전단력 및 휨모멘트, 데크의 수평변위, 그리고 케이블 장력 등의 상충하는 지진응답들을 동시에 효과적으로 제어함으로써 지진응답제어에 매우 효율적인 제어전략이 될 수 있음을 보였다. This paper proposes semi-active fuzzy control technique of magneto-rheological dampers for seismic response control of cable-stayed bridges. Through the fuzzy inference process, the proposed technique performs the semi-active control with the responses of MR dampers only. Moreover, differently from the conventional semi-active control technique, this technique does not require additional active controller for the primary controller, which provides a simple design process. in order to validate the control performance of the proposed technique, the semi-active fuzzy control technique is applied to the benchmark control problem of cable-stayed bridge and its control performance is compared with those of conventional semi-active control techniques. The comparative results show that the proposed fuzzy control technique can be an effective control strategy by efficiently and simultaneously reducing the mutual conflicting responses such as the shear forces and moments at the base of the lowers, longitudinal displacement of the deck, and tensions in the stay cables.

마찰 슬라이딩 거동을 보이는 건물 내 중량 설비의 내진성능 향상을 위한 감쇠기 연결 방안

옥승용,박관순,이지호 한국안전학회 2020 한국안전학회지 Vol.35 No.1

This study proposes a new damper configuration for seismic performance improvement of heavy sliding facilities inside a building. For this purpose, we deal with two connection types of control system, and the parametric study has been performed to investigate their comparative seismic performances according to the variations of the control capacity. In order to simulate the seismic responses of the proposed system, we employed a recently-developed seismic response analysis method that can deal with the two-mass system with nonlinear frictional sliding behavior. The numerical results demonstrate that the typical method of diagonal bracing damper connection can exhibit effective control performance both on structure and the heavy sliding facilities, whereas the structure-facilities connection method does not show any control effect on both responses. On the other hand, the typical method has some limitations that it can adversely cause excessive sliding of the facilities, depending upon the frequency characteristics of structure and earthquake. On the contrary, the structure-facilities connection method is very effective in reducing the sliding displacement of the heavy facilities, even with small amount of control capacity. Thus, the following potential expectations can be inferred from these results: The typical diagonal bracing damper connection method will have some promising benefits in controlling the sliding facilities inside the building as well as the building itself, and the structure-facilities connection method can be a cost-effective way of protecting the internal heavy important facilities inside the structure already designed with sufficient seismic performance.

하중 및 모델 불확실성에 따른 래선반구조물의 파괴모드멸 신뢰성 평가 및 경향성 분석

옥승용 ( Seung Yong Ok ) 한국안전학회(구 한국산업안전학회) 2013 한국안전학회지 Vol.28 No.7

According to recent statistics of fatalities and injuries in warehouses, the collision of forklift to storage rack structures is one of the major accidents. Due to the randomness of forklift-colliding event and inherent uncertainties in the impact loading and the structural model, the quantitative assessment of the structural safety of the forklift-colliding rack structure can be treated by the probabilistic approaches such as FORM, SORM and MCS, etc. In order to investigate the reliability of the rack structure, several component-level failure modes are taken into account and the assessment results of the corresponding failure probabilities are verified in comparison with the FORM, SORM and MCS results. The numerical results demonstrate that FORM is the most numerically efficient method with less accurate assessment results and MCS is the accurate but numerically inefficient method, whereas SORM is both the accurate and numerically efficient method. Further, Parametric studies on the level of the uncertainties in the load and model parameters demonstrate that the failure probability of the rack is increased as the uncertainty level is increased, and vice versa.

추계학적 선형화 방법 및 다목적 유전자 알고리즘을 이용한 지진하중을 받는 인접 구조물에 대한 비선형 감쇠시스템의 최적 설계

옥승용 송준호 고현무,박관순 한국지진공학회 2007 한국지진공학회논문집 Vol.11 No.6

인접 구조물의 지진응답 제어를 위한 비선형 감쇠시스템의 최적 설계 방법에 관하여 연구하였다. 최적 설계를 위한 목적 함수로는 구조물의 응답과 감쇠기의 총 사용량을 고려하였으며, 상충하는 두 목적함수를 합리적인 수준에서 동시에 최소화하는 해를 구하기 위하여 유전자 알고리즘에 기반한 다목적 최적화 방법을 도입하였다. 또한, 최적화 과정에서 요구되는 비선형 시간이력해석을 수행하지 않고도, 비선형 이력감쇠기로 연결된 구조물의 지진응답을 효율적으로 평가하기 위하여 추계학적 선형화 방법을 접목하였다. 제시하는 방법의 효율성을 검증하기 위한 수치 예로서 20층과 10층의 인접 빌딩을 고려하였으며, 두 빌딩을 연결하는 비선형 감쇠시스템으로는 입력전압의 크기에 따라 변화하는 감쇠성능을 보이는 MR 감쇠기를 도입하였다. 제시하는 방법을 통하여 MR 감쇠기의 각 층별 최적 개수 및 감쇠용량을 결정할 수 있었으며, 이는 일반적인 균등분포 시스템에 비해 유사한 제어성능을 보이면서도 훨씬 경제적이었다. 또한, 인접구조물간 충돌에 대하여도 확률적으로 안정적인 거동을 보임을 검증하였으며, 제시하는 방법이 준능동 제어시스템의 최적 배치를 결정하기 위한 설계문제에도 적용할 수 있음을 보였다. Optimal design method of nonlinear damping system for seismic response control of adjacent structures is studied in this paper. The objective functions of the optimal design are defined by structural response and total amount of the dampers. In order to obtain a solution minimizing two mutually conflicting objective functions simultaneously, multi-objective optimization technique based on genetic algorithm is adopted. In addition, stochastic linearization method is embedded into the multi-objective framework to efficiently estimate the seismic responses of the adjacent structures interconnected by nonlinear hysteretic dampers without performing nonlinear time-history analyses. As a numerical example to demonstrate the effectiveness of the proposed technique, 20-story and 10-story buildings are considered and MR dampers of which hysteretic behaviors vary with the magnitude of the input voltage are considered as nonlinear hysteretic damper interconnecting two adjacent buildings. The proposed approach can provide the optimal number and capacities of the MR dampers, which turned out to be more economical than the uniform distribution system while maintaining similar control performance. The proposed damper system is verified to show more stable performance in terms of the pounding probability between two adjacent buildings. The applicability of the proposed method to the design problem for optimally placing semi-active control system is examined as well.