http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
오정균,장정식 한국공업화학회 2015 한국공업화학회 연구논문 초록집 Vol.2015 No.0
The electrodes of electrochemical capacitors (ECs) composed of carbon nanofiber decorated three-dimensional graphene (CPSC-3rGO) were fabricated by single-nozzle co-electrospinning, freeze drying and chemical reduction methods. Polypyrrole was coated on the SnO2/Co3O4 nanofibers using vapor deposition polymerization (VDP). Then, these nanofibers were mixed with aqueous graphene oxide (GO) solution and freeze dried to form 3D structures. The CPSC-3rGOs were synthesized by thermal reduction of these 3D structures to improve the power density of EC electrodes. As result, these devices showed greater electrical performance and flexibility than that of the other 3D nanomaterials.
사전위상 왜곡을 이용한 IEEE 802.11a OFDM 무선랜 전력증폭기 위상왜곡 특성분석
오정균,구경헌,최재홍 대한전자공학회 2005 電子工學會論文誌-TC (Telecommunications) Vol.42 No.2
In this paper, 2-stage power amplifier has been designed for 5.8GHz wireless LAN application. The power amplifier P1dB output power has 21.6dBm at 5.8GHz frequency. Also the power amplifier shows 17.6dB gain and -17.8dB input return loss at 5.725GHz to 5.825GHz. The OFDM modulation and transmission block have been modeled in order to analyse the relationship between the power amplifier distortion and output ACPR for the IEEE 802.11a wireless LAN. The nonlinear characteristic of the power amplifier has been modeled as AM-to-AM and AM-to-PM using the behavioral model, and the output spectrum is analysed with the phase distortion variation. Also, amplifier back-off value from P1dB to satisfy the required IEEE 802.11a standard spectrum mask has been simulated with phase distortion, and the simulation data have been compared to the measurement result collected by using the pre-distortion technique. 본 논문에서는 5.8GHz 무선랜에 적용할 수 있는 전력증폭기를 설계 및 제작하였다. 제작된 전력증폭기는 2단으로 구성되며 측정결과 중심주파수 5.8GHz에서 21.6dBm의 P1dB 출력전력과 100MHz 대역에서 17.6dB 이득과 -17.8dB 이하의 입력반사손실을 얻었다. 설계된 전력증폭기의 왜곡과 출력 ACPR 관계를 분석하기위해, 최대 54Mbps의 전송속도를 가지는 IEEE 802.11a OFDM 변조부와 송신부를 모델링하였다. 전력증폭기의 비선형특성은 behavioral model을 이용하여 AM-to-AM과 AM-to-PM으로 모델링하였으며, 위상 왜곡에 따른 출력스펙트럼 특성을 해석하였다. IEEE 802.11a 무선랜 시스템의 요구 출력스펙트럼 마스크를 만족하기위한 P1dB로부터 back-off값을 구하기 위하여 위상왜곡에 따른 전력증폭기의 ACPR 특성을 시뮬레이션하고 사전왜곡방식을 이용하여 증폭기의 위상왜곡을 변화시키며 측정한 결과와 시뮬레이션 특성을 비교 제시하였다.
기존의 핵산증폭기를 사용한 유리슬라이드상에서의 원위치 중합효소 연쇄반응
오정균,장진수,이재영 한국미생물학회 2003 미생물학회지 Vol.39 No.3
In order to establish effective in situ PCR on the glass slide using the conventional DNA thermal cycler, several parameters should be considered. These include full accessibility of PCR reagents into the cells, prevention of diffusing PCR products out of the cells, loss of PCR reagents by nonspecific adherence onto the glass slide, dryness of PCR reagents by heat, and heat conductivity from the heat block to the glass slide. Especially, to guarantee the full accessibility of PCR reagents to sample, relatively higher concentration of PCR reagents (particularly 4.5 mM of $Mg^{++}$) was required while 5 to 10 units/50 ${\mu}l$ reaction of Taq enzyme was enough as long as the step of pre-PCR incubation was included. Dryness of sample was prevented by addition of distilled water into the empty slots in the heat block, thereby providing the reproducible temperature-time profile of PCR. Observed temperature was lower than the programmed temperature by 3 to $4^{\circ}C$. 기존의 핵산증폭기를 사용하여 유리 슬라이드상에서의 효과적인 원위치 중합효소 연쇄반응(in situ PCR)을 수행하기 위해서는 여러 가지 조건들을 고려해야 하는데, 이러한 조건에는 PCR 용액의 세포속으로의 침투, 증폭된 PCR산물의 세포외 유출의 방지, PCR용 액 성분의 유리슬라이드로의 비특이적 부착으로 인한 손실, 열에 의한 시약의 증발, heat block으로부터 슬라이드로의 열전도성 둥이 있다. 특히 PCR용액 성분의 세포내로의 침투를 보장하기 위해서는 다소 높은 농도의 PCR 용액성분(특히 4.5 mM $MgCl_{2}$ 농도)이 필요하였고, Taq 효소는 PCR전 처리(pre-PCR incubation)를 수행하는 경우,50 ${\mu}l$ 반응당 5~10 units이면 충분하였다. 또한 PCR의 전형적인 온도-시간 양상(temperature-time profile)을 만족시키기 위해서는 먼저 샘플의 건조화를 방지해야 하는데, 이를 위해서 heat block속의 빈 공간에 적당량의 물을 첨가했고, 설정온도와 실제온도를 측정해본 결과 약3~$4^{\circ}C$의 차이가 있었다.
IEEE 802.11g OFDM 무선랜용 2.4GHz 전력증폭기의 비선형 왜곡분석
오정균,최재홍,구경헌,Oh Chung Gyun,Choi Jae Hong,Koo Kyung Heon 대한전자공학회 2005 電子工學會論文誌-TC (Telecommunications) Vol.42 No.3
무선랜용 전력증폭기의 비선형특성과 출력 ACPR 관계를 분석하기위해, 최대 54Mbps의 전송속도를 가지는 IEEE 802.11g OFDM 변조부와 송신부를 모델링하였다. 2.4GHz 전력증폭기의 비선형특성은 behavioral model을 이용하여 An-to-AM과 AM-to-PM으로 모델링하였으며, 위상 왜곡특성에 따른 출력스펙트럼 특성을 해석하였다. IEEE 802.11g 무선랜 시스템의 요구 출력스펙트럼 마스크를 만족하기위한 P1dB로부터 back-off값을 구하기 위하여 모델링한 위상왜곡 크기에 따른 전력증폭기의 ACPR 특성을 시뮬레이션하고 사전위상 왜곡방식을 이용하여 증폭기의 위상왜곡을 변화시키며 측정한 결과와 시뮬레이션 특성을 비교 제시하였다. The OFDM modulation and transmission block have been modeled in order to analyse the relationship between the 2.4GHz power amplifier distortion and output ACPR for the IEEE 802.11g wireless LAN. The nonlinear characteristic of the power amplifier has been modeled as AM-to-AM and AM-to-PM using the behavioral model, and the output spectrum is analysed with the phase distortion variation. Also, amplifier back-off value from P1dB to satisfy the required IEEE 802.11g standard spectrum mask s been simulated with modeled phase distortion, and the simulation data have been compared to the measured result by using the pre-distortion technique.