Effect of Hysteresis on Interface Waves in Contact Surfaces

김노유,양승용 한국비파괴검사학회 2010 한국비파괴검사학회지 Vol.30 No.6

This paper describes a theoretical model and acoustic analysis of hysteresis of contacting surfaces subject to compression pressure. Contacting surfaces known to be nonlinear and hysteretic is considered as a simple spring that has a complex stiffness connecting discontinuous displacements between two solid contact boundaries. Mathematical formulation for 1-D interfacial wave propagation between two contacting solids is developed using the complex spring model to derive the dispersion relation between the interface wave speed and the complex interfacial stiffness. Existence of the interface wave propagating along the hysteretic interface is studied in theory and discussed by investigating the solution to the dispersion equation. Unlike the linear interface without hysteresis, there can exist only one distinct mode of interface waves for the hysteretic interface, which is anti-symmetric motion. The anti-symmetric mode of interface wave propagates with the velocity faster than the Rayleigh surface wave but less than the shear wave depending on the interfacial stiffness. If the contacting surfaces are compressed so much that the linear interfacial stiffness is very high, the hysteretic stiffness does not affect the interface wave velocity. However, it has an effect on the speed of interface wave for a loosely contact surfaces with a relatively low linear stiffness. It is also found that the phase velocity of anti-symmetric wave mode converges to the shear wave velocity in despite of the linear stiffness value if the hysteretic stiffness approaches 0.5.

Estimation of Hysteretic Interfacial Stiffness of Contact Surfaces

김노유 한국비파괴검사학회 2013 한국비파괴검사학회지 Vol.33 No.3

This paper proposes an ultrasonic method for measurement of linear and hysteretic interfacial stiffness of contacting surfaces between two steel plates subjected to nominal compression pressure. Interfacial stiffness was evaluated by the reflection and transmission coefficients obtained from three consecutive reflection waves from solid-solid surface using the shear wave. A nonlinear hysteretic spring model was proposed and used to define the quantitative interfacial stiffness of interface with the reflection and transmission coefficients. Acoustic model for 1-D wave propagation across interfaces is developed to formulate the reflection and transmission waves and to determine the linear and nonlinear hysteretic interfacial stiffness. Two identical plates are put together to form a contacting surface and pressed by bolt-fastening to measure interfacial stiffness at different states of contact pressure. It is found from experiment that the linear and hysteretic interfacial stiffness are successfully determined by the reflection and transmission coefficient at the contact surfaces through ultrasonic pulse-echo measurement.

Ultrasonic Evaluation of Interfacial Stiffness for Nonlinear Contact Surfaces

김노유,김현동,조윤호 한국비파괴검사학회 2008 한국비파괴검사학회지 Vol.28 No.6

This paper proposes an ultrasonic measurement method for measurement of linear interfacial stiffness of contacting surface between two steel plates subjected to nominal compression pressures. Interfacial stiffness was evaluated by using shear waves reflected at contact interface of two identical solid plates. Three consecutive reflection waves from solid-solid surface are captured by pulse-echo method to evaluate the state of contact interface. A non-dimensional parameter defined as the ratio of their peak-to-peak amplitudes are formulated and used to calculate the quantitative stiffness of interface. Mathematical model for 1-D wave propagation across interfaces is developed to formulate the reflection and transmission waves across the interface and to determine the interfacial stiffness. Two identical plates are fabricated and assembled to form contacting surface and to measure interfacial stiffness at different states of contact pressure by means of bolt fastening. It is found from experiment that the amplitude of interfacial stiffness is dependent on the pressure and successfully determined by employing pulse-echo ultrasonic method without measuring through-transmission waves.

비선형 균열에 의한 초음파의 주파수 변조 특성

김노유 한국비파괴검사학회 2011 한국비파괴검사학회지 Vol.31 No.6

Stochastic Estimation of Acoustic Impedance of Glass-Reinforced Epoxy Coating

김노유,나환선 한국비파괴검사학회 2014 한국비파괴검사학회지 Vol.34 No.2

An epoxy coating applied to the concrete surface of a containment building deteriorates in hazardous environments such as those containing radiation, heat, and moisture. Unlike metals, the epoxy coating on a concrete liner absorbs and discharges moisture during the degradations process, so it has a different density and volume during service. In this study, acoustic impedance was adopted for characterizing the degradation of a glass-reinforced epoxy coating using the acoustic reflection coefficient (reflectance) on a rough epoxy coating. For estimating the acoustic reflectance on a wavy epoxy coating surface, a probabilistic model was developed to represent the multiple irregular reflections of the acoustic wave from the wavy surface on the basis of the simulated annealing technique. A number of epoxy-coated concrete specimens were prepared and exposed to accelerated aging conditions to induce an artificial aging degradation in them. The acoustic impedance of the degraded epoxy coating was estimated successfully by minimizing the error between a waveform calculated from the mathematical model and a waveform measured from the surface of the rough coating.

Ultrasonic Estimation and FE Analysis of Elastic Modulus of Kelvin Foam

김노유,양승용 한국비파괴검사학회 2016 한국비파괴검사학회지 Vol.36 No.1

The elastic modulus of a 3D-printed Kelvin foam plate is investigated by measuring the acoustic wave velocity of 1 MHz ultrasound. An isotropic tetrakaidecahedron foam with 3mm unit cell is designed and printed layer upon layer to fabricate a Kelvin foam plate of 14mm thickness with a 3D CAD/printer using ABS plastic. The Kelvin foam plate is completely filled with paraffin wax for impedance matching, so that the acoustic wave may propagate through the porous foam plate. The acoustic wave velocity of the foam plate is measured using the time-of-flight(TOF) method and is used to calculate the elastic modulus of the Kelvin foam plate based on acousto-elasticity. Finite element method(FEM) and micromechanics is applied to the Kelvin foam plate to calculate the theoretical elastic modulus using a non-isotropic tetrakaidecahedron model. The predicted elastic modulus of the Kelvin foam plate from FEM and micromechanics model is similar, which is only 3-4% of the bulk material. The experimental value of the elastic modulus from the ultrasonic method is approximately twice as that of the numerical and theoretical methods because of the flexural deformation of the cell edges neglected in the ultrasonic method.

Acoustic Estimation of Phase Velocity of Closed-Cell Kelvin Structure based on Spectral Phase Analysis

김노유 국제문화기술진흥원 2022 International Journal of Advanced Culture Technolo Vol.10 No.3

In this paper, the effect of porosity on the acoustic phase velocity of the 3D printed Kelvin closed-cell structure was investigated using the spectral phase analysis. Since Kelvin cells bring about the large amount of scattering, acoustic pulses in ultrasonic measurements undergoes a distortion of waveforms due to the dispersion effect. In order to take account on the dispersion, mathematical expressions for calculating the phase velocity of longitudinal waves propagating normal to the plane of the Kelvin structure are suggested by introducing a complex wave number based on Fourier transform. 3D Kelvin structure composed of identical unit-cells, a polyhedron of 14 faces with 6 quadrilateral and 8 hexagonal faces, was developed and fabricated by 3D CAD and 3D printer to represent the micro-structure of porous materials such as aluminum foam and cancellous bone. Total nine samples of 3D Kelvin structure with different porosity were made by changing the thickness of polyhedron. Ultrasonic pulse of 1MHz center frequency was applied to the Kelvin structures for the measurement of the phase velocity of ultrasound using the TOF(time-of-flight) and the phase spectral method. From the experimental results, it was found that the acoustic phase velocity decreased linearly with the porosity.

12" 웨이퍼 Spin etcher용 실시간 박막두께 측정장치의 개발

김노유,서학석 한국반도체디스플레이기술학회 2003 한국반도체장비학회지 Vol.2 No.2

This paper proposes a thickness measurement method of silicon-oxide and poly-silicon film deposited on 12" silicon wafer for spin etcher. Halogen lamp is used as a light source for generating a wide-band spectrum, which is guided and focused on the wafer surface through a optical fiber cable. Interference signal from the film is detected by optical sensor to determine the thickness of the film using spectrum analysis and several signal processing techniques including curve-fitting and adaptive filtering. Test wafers with three kinds of priori-known films, polysilicon(300 nm), silicon-oxide(500 nm) and silicon-oxide(600 nm), are measured while the wafer is spinning at 20 Hz and DI water flowing on the wafer surface. From experiment results the algorithm presented in the paper is proved to be effective with accuracy of maximum 0.8% error.rror.

고문서 거란문자의 능동형 적외선 열영상 가시화

김노유,정재영 국제문화기술진흥원 2022 The Journal of the Convergence on Culture Technolo Vol.8 No.2

양피지로 만들어진 고문서에 필사된 후 오랜 시간동안 부식되고 자연 훼손되어 해독하기 어려운 거란문자를 문서를 손상시키지 않으면서 비접촉방식으로 가시화하기 위해 능동형 적외선 열화상 기술을 개발하였다. 문서 표면에 할로겐 램프를 이용하여 광대역 적외선을 정현파 형태로 변조/입사시키면서 서체 부분과 기록용지 표면으로부터 차별 적으로 방사되는 적외선을 영상화함으로서 훼손되어 잘 보이지 않는 고대 글자를 가시화 하였다. 능동형 적외선 영상 으로부터 거란 문자로 추정되는 문자들을 기존의 광학영상이나 적외선 영상보다 명확하게 판독할 수 있었으며 그 결 과로서 영어 알파벳의 ‘d’ 음가를 가지는 거란문자인 ‘ ’나 ‘ri’ 발음의 거란문자인 ‘ ’를 포함하여 다양한 거란문자를 확인할 수 있었다. 이로서 본 연구를 통해 개발된 능동형 적외선 기술이 향후 고문서 자료의 디지털 복원과 보존에 능동형 적외선 열화상기술이 효과적으로 활용될 수 있을 것으로 기대된다. Unreadable Khitan scripts of ancient documents written by indian ink on parchment(sheepskin) are visualized by active infrared thermography without contacting and damaging the document which are deteriorated and aged presumably over many years. Sinusoidal infrared thermal wave using Halogen lamp is applied to the surface of the document in order to selectively magnify and record the thermal response of indian ink. The infrared image of the document captured in real time by infrared camera under the active external excitation shows the better sharpness and readability of Khitan characters than the optical image, from which many Khitan letters like ‘ ’ and ‘ ’ sounding as ‘d’ and ‘ri’ in English alphabet are detected and deciphered. It is concluded from the experiment that the active infrared thermography can be used as a promising method for digital reconstruction and preservation of ancient documents in the future.

적응필터를 이용한 적층 복합재료에서의 역산란 X-Ray 신호처리 및 복원

김노유 한국비파괴검사학회 2000 한국비파괴검사학회지 Vol.20 No.6

충격에 의해 복합 재료 내에 발생하는 층간 박리를 정량적으로 평가하기 위한 비파괴 방법중에서 Compton X-ray 역산란 기술은 초음파에 비해 비접촉식이며 박리 층간의 상호간섭이 없어 복합재료의 박리 층과 같은 미세한 결함의 측정을 위해 측정 정도를 높이면 역산란 기술에 있어서 복합재료의 박리 층과 같은 미세한 결함의 측정을 위해 측정 정도를 높이면 역산란 양의 감소로 인해 신호 대 잡음 비(SNR)가 급격히 감소하여 결함검출 가능성이 크게 저하된다. 본 논문에서는 복합재료의 특성을 고려한 X-ray 역산란 모델을 기초로 적응필터를 사용하여 결함신호를 비선형 감쇄, 빔 경화(X-ray hardening), 비균질 특성과 같은 잡음 신호로부터 분리, 추출하는 방법을 제시하였다. 이렇게 분리된 결함신호로부터 분리, 추출하는 방법을 제시하였다. 이렇게 분리된 결함신호로부터 정량적인 결함(박리)의 위치와 크기를 수학적 산란 모델과의 비교를 통해 최소 자승법을 이용하여 결정하였다. Compton X-ray backscatter technique has been used to quantitatively assess the impact damage in quasi-isotropic laminated composites and to obtain a cross-sectional profile of impact-damaged laminated composites from the density variation of the cross section. An adaptive filter is applied to the Compton backscattering data for the reconstruction and noise reduction from many sources including quantum noise, especially when the SNR(signal-to-noise ratio) of the image is relatively low. A nonlinear reconstruction model is also proposed to overcome distortion of the Compton backscatter image due to attenuation effects, beam hardening, and irregular distributions of the fibers and the matrix in composites. Delaminations masked or distorted by the first few delaminations near the front surface are detected and characterized, both in width and location, by application of an error minimization algorithm.