http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
이성호,홍성석,구형회 한국군사과학기술학회 2000 한국군사과학기술학회지 Vol.3 No.2
Thermal gradient chemical vapor infiltration (TG-CVI) process, which is one of the CVI techniques to densify a porous fiber preform, requires for a heater to have uniform surface temperature distribution. Thus, it is essential to design the shape of the heater and to predict the temperature distribution when the heater has a profile which is not a simple cylinder. In this study, an analytical method has been used to design the inner profile of a conical heater showing uniform temperature distribution, if its outer shape is specified. Temperature distribution on the heater surface has been calculated with the finite difference method and compared with the experimental results. When a heater had a combined profile with a large cone and a small cylinder, temperature was higher in the cylindrical part. To reduce the temperature difference between these areas, a hole-machining method has been proposed including other possible ones. A shape design and optimization program has been made to improve the temperature uniformity of the TG-CVI heater better than that designed with the analytical method.
권순용,정대영,최시경,구형회,이종수 한국세라믹학회 1994 한국세라믹학회지 Vol.31 No.8
Sessile drop studies of molten Al on single crystal sapphire substrate were conducted to understand the wetting behavior and interfacial reaction at Al/Al2O3 interface. To investigate the wetting mechanism, the variation in contact angle was determined with time. The contact angle obtained in this study decreased exponentially with time. This result means that the driving force for wetting is the reduction in interfacial energy between liquid Al and sapphire caused by the interfacial reaction. The closer examination revealed that the reaction was the dissolution of sapphire by molten Al. Ti has been frequently used to improve wetting on ceramic materials. Therefore, the influence of Ti content on the wetting behaviour was investigated in this work. The equilibrium wetting angles of pure Al, Al-0.3 wt%Ti, and Al-1.0 wt%Ti at 100$0^{\circ}C$ were 63$^{\circ}$, 59$^{\circ}$, and 54$^{\circ}$respectively. The difference is considered as the result of the change in interfacial energy caused by the reaction between Ti and sapphire and the interfacial reaction formed the reaction products of varying stoichiometry (TiO, Ti2O3, TiO2 etc.).
추진기관 노즐용 Needle Punch 탄소/탄소 복합재료 제조
조대현,조채욱,이종문,구형회,이재열,윤남균 한국추진공학회 2008 한국추진공학회 학술대회논문집 Vol.2008 No.11
추진기관용 노즐에 사용하는 대표적인 소재로는 흑연소재와 탄소/탄소 복합재료를 들 수 있다. 흑연 소재는 열충격 저항성이 취약하여 사용 중 파손의 발생가능성이 높아 현재는 열축격 저항성이 우수한 탄소/탄소 복합재료를 주로 사용하고 있다. 본 연구를 통하여 수입에 의존하였던 Quasi-3D 구조의 니들펀치(Needle Punch) 프리폼을 국산화 개발하였다. 본 연구에서는 니들펀치 프리폼의 제조 공정 및 밀도화 공정을 다루고자 한다.
세라믹-금속 브레이징 접합조인트의 고온 접합강도에 관한 연구
이수정,정명영,이대길,구형회,Lee, Su-Jeong,Jeong, Myung-Yeong,Lee, Dai-Gil,Goo, Hyung-Hoi 대한기계학회 1996 大韓機械學會論文集A Vol.20 No.2
Four point bending tests of the brazed joint composed of sintered silicon nitride and 0.2% carbon steel with Cusil ABA filler which were fabricated at 86$0^{\circ}C$ were performed at temperatures, 25, 100, 200, 300, 400, 50$0^{\circ}C$ From the experiments, the maximum bending strength was measured at 30$0^{\circ}C$ From the 3D FE analysis of the residual stress of the brazed joint, it was revealed that the thermally induced residual stresses were minimized when the environmental temperature was 35$0^{\circ}C$ Considering the degradation of the filler material at high temperatures, it was calculated that the maximum bending strength of the brazed joint occured just below the temperature of the minimum thermal residual stress and the thermal residual stress was the dominative parameter of the brazed joint.