http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
폴리비닐리덴플루오라이드로 코팅한 폴리아닐린센서의 메탄올에 대한 감응 특성과 장기안정도 고찰
손성옥,김정숙,허증수,Sohn Sung-Ok,Kim Jung-Suk,Huh Jeung-Soo 한국재료학회 2004 한국재료학회지 Vol.14 No.4
The problem of polyaniline (PANi) sensor has been poor mechanical and chemical stability under atmosphere condition. In order to overcome these problems, the PANi sensor coated with polyvinylidenefluoride ($PVF_2$) was employed. The morphology of $PVF_2$ coated-PANi layer was showed smooth and transparent properties at 15% concentration of coating solution. The resistance of $PVF_2$ coated-PANi was kept at constant value and had a good stability at long-term periods in presence of humidity.
초음파 처리에 의해 합성된 ZnO 나노로드 센서의 일산화질소 가스에 대한 감응 특성
박순민,쟝샤오린,허증수,Park, Sun-Min,Zhang, Shao-Lin,Huh, Jeung-Soo 한국재료학회 2008 한국재료학회지 Vol.18 No.7
ZnO nanorod gas sensors were prepared by an ultrasound radiation method and their gas sensing properties were investigated for NO gas. For this procedure, 0.01, 0.005 and 0.001M of zinc nitrate hydrate [$Zn(NO_3)_2\;{\cdot}\;6H_2O$] and hexamethyleneteramine [$C_6H_{12}N_4$] aqueous solutions were prepared and then the solution was irradiated with high intensity ultrasound for 1 h. The lengths of ZnO nanorods ranged from 200 nm to 500 nm with diameters ranging from 40 nm to 80 nm. The size of the ZnO nanorods could be controlled by the concentration of solution. The sensing characteristics of these nanostructures were investigated for three kinds of sensor. The properties of the sensors were influenced by the morphology of the nanorods.
Sol-Coprecipitation 법에 의한 NO 감지용 $WO_3$ 센서 제조시 pH의 영향
김석봉,이대식,이덕동,허증수,Kim, Suk-Bong,Lee, Dae-Sik,Lee, Duk-Dong,Huh, Jeung-Soo 한국센서학회 2001 센서학회지 Vol.10 No.2
입자들이 용액에 녹아있을 때 pH에 따라서 다른 zeta-potential을 가지게 되며, 이것은 입자의 분산상태에 영향을 주게 된다. NO 센서에서 $WO_3$ 입자의 크기는 감도에 큰 영향을 끼치므로 Sol-Coprecipitation법에 의한 $WO_3$ 센서 제조 시에 $WO_3$ precursor 상태에서의 pH의 영향을 알아보았다. 먼저 $WO_3$ precursor의 전기적 포텐셜을 측정하여 pH가 2에서 7로 변함에 따라 mobility가 증가하여 7일 때에 가장 큰 분산도를 가진 것을 알 수 있었고, 이는 powder 제조 후 입도 분석, 감지막의 XRD peak, 표면사진으로부터 확인 할 수 있었다. 결과적으로 감도 특성에도 영향을 끼쳐 pH=7에서 제조한 센서가 다른 pH에서 제조한 센서보다 감도가 우수한 것으로 나타났다. When particles are dissolved in solution, they have different zeta-potentials depending on pH. Zeta-potential has an influence on particle separation, which can control particle size. And the size of $WO_3$ particle affects the sensitivity of $WO_3$ sensor for detecting NO gas. Therefore we study influence of pH on NO-sensing $WO_3$ gas sensor fabricated by Sol-Coprecipitation method. As pH increases from 2 to 7, dynamic mobility of $WO_3$ precursor was increased. When pH was 7, it showed the largest distribution separation. It means when pH is 7, we can make $WO_3$ powder which has smaller particle size. And it is confirmed by particle size analysis of $WO_3$ powder, X-ray diffration result of $WO_3$ sensing layer and surface morphology. It also affect NO sensing characteristics of $WO_3$ gas sensor. The sensing film synthesized at pH 7 showed the largest sensitivity.
이지훈,박재범,박단비,허증수,임정옥,Lee, Jihoon,Park, Jaebum,Park, Danbi,Huh, Jeung Soo,Lim, Jeong Ok 한국재료학회 2021 한국재료학회지 Vol.31 No.7
Graphene, a new material with various advantageous properties, has been actively used in various fields in recent years. Applications of graphene oxide are increasing in combination with other materials due to the different properties of graphene oxide, depending on the number of single and multiple layers of graphene. In this study, single-layer graphene oxide and multi-layer graphene oxide are spray coated on polystyrene, and the physicochemical properties of the coated surfaces are characterized using SEM, Raman spectroscopy, AFM, UV-Vis spectrophotometry, and contact angle measurements. In single-layer graphene oxide, particles of 20 ㎛ are observed, whereas a 2D peak is less often observed, and the difference in surface height increases according to the amount of graphene oxide. Adhesion increases with an increase in graphene oxide up to 0.375 mg, but decreases at 0.75 mg. In multi-layer graphene oxide, particles of 5 ㎛ are observed, as well as a 2D peak. According to the amount of graphene oxide, the height difference of the surface increases and the adhesive strength decreases. Both materials are hydrophilic, but single-layer graphene oxide has a hydrophilicity higher than that of multi-layer graphene oxide. We believe that multi-layer graphene oxide and single-layer graphene oxide can be implemented based on the characteristics that make them suitable for application.
휘발성유기화합물가스에 대한 폴리아닐린 센서의 감도 향상
유준부,유비,임정옥,변형기,허증수,Yu, Joon-Boo,Liu, Fei,Lim, Jeong-Ok,Byun, Hyung-Gi,Huh, Jeung-Soo 한국재료학회 2007 한국재료학회지 Vol.17 No.8
Nano-structured polyaniline have been synthesized by interfacial polymerization method at room temperature. An aqueous solution of aniline in chloroform and another solution of ammonium peroxydisulfate in doping acid were prepared at different times terminated with methanol at room temperature. SEM, UV-vis were used to characterize the polyaniline with regard to their morphology and structure. The diameter and length of polyaniline can be controlled by the reaction time. Nano-structured polyaniline were found to have superior sensitivity for volatile organic compounds(VOCs). As the reaction time to increase from 30minute to 2hours the sensitivity were decreased to VOCs vapors. The sensitivity of Nano-structured polyaniline sensor appeared to VOCs better than the sensitivity of chemical synthesis sensors. The sensitivity of Nano-structured polyaniline sensor improved benzene vapors.
$BCI_3/H_2/Ar$ 유도결합 플라즈마를 이용한 GaN의 건식 식각에 관한 연구
김성대,정석용,이병택,허증수,Kim, Sung-Dae,Jung, Seog-Yong,Lee, Byung-Taek,Huh, Jeung-Soo 한국재료학회 2000 한국재료학회지 Vol.10 No.3
$BCI_3/H_2/Ar$ ICP(Inductively Coupled Plasma)를 이용한 GaN이 건식식각에 있어서 공정변수들이 식각 특성에 미치는 영향을 분석하고 적정조건을 도출하였다. 연구 결과 식각속도와 측벽수직도 공히 ICP 전력, bias 전압과 $BCI_3$ 조성의 증가, 공정압력의 감소에 의해 현저히 증가하며, 온도의 증가에 따라 다소간 증가하였고, 온도의 증가에 따라 다소간 증가하였고, $BCI_3$조성이 가장 큰 영향을 미쳤다. 표면거칠기는 bias 전압 증가에 의해 크게 향상, $BCI_3$ 조성의 감소에 따라 향상되었으며 다른 변수는 큰 영향을 미치지 않았다. 결과적으로 ICP 전력 900W, bias 전압 400V, $BCI_3$ 조성 60%, 공정압력 4mTorr의 조건에서 175nm/min 정도의 $CI_2$ 사용 시와 유사한 높은 식각속도와 평탄한 표면이 얻어졌다. Bias 전압이 낮은 경우 식각 후 시료 표면에 $GaC_x$로 추정되는 식각부산물이 관찰되었다. The reactive ion etching process of GaN using $BCI_3/H_2/Ar$ high density inductively coupled plasma was investigated. Results showed that both of the etch rate and the sidewall verticality significantly increased as the ICP power, bias voltage, and the $BCI_3$ ratio were increased whereas effects of the other variables were minimal. The maximum etch rate of about 175nm/min was obtained at the condition of ICP power 900W, bias voltage 400V, 4mTorr, and 60% $BCI_3$, which resulted in reasonably smooth etched surface. Etch residues were observed in the case of samples etched at the low bias conditions, which were proposed to be as the $GaCI_x$ compounds.
Impedance를 이용한 전도성고분자 센서의 에탄올 가스 감응특성
이경문,유준부,전희권,이병수,이덕동,허증수,Lee, Kyung-Mun,Yu, Joon-Boo,Jun, Hee-Kwon,Lee, Byung-Soo,Lee, Duk-Dong,Huh, Jeung-Soo 한국재료학회 2003 한국재료학회지 Vol.13 No.3
The polypyrrole and polyaniline thin film sensors which were made by chemical polymerization were employed to detect ethanol gas. With a single sensor element we can obtain characteristic patterns of behaviour across a very wide frequency range when measuring either resistance or capacitance. Impedance spectroscopy was employed to study the gas sensing behavior of both capacitance and resistance based sensors with conducting polymer as the active sensing element.