http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
한영민(Youngmin Han),황석민(Seokmin Hwang),성미영(MeeYoung Sung) 한국정보과학회 2005 한국정보과학회 학술발표논문집 Vol.32 No.2
일반적인 렌더링 방식은 응용→기하→래스터화로 진행되는 렌더링 파이프라인 상에서 진행된다. 그래픽 카드의 발전으로 기하 단계의 연산을 GPU가 담당함에 따라 CPU의 연산을 줄여 CPU가 많은 연산을 할 수 있게 되었다. 그러나 이 같은 분배로 인해 CPU와 GPU가 서로 끝나기를 기다리는 병목현상이 발생하게 되었다. 이러한 병목 현상은 효율적인 렌더링을 저해하는 요인이다. 본 연구의 목적은 CPU와 GPU의 병렬처리 과정에서 발생하는 병목현상을 줄여 실시간 렌더링에서 그래픽 출력을 더욱 빠르게 하는데 있다. 이를 위해 본 논문에서는 그래픽 출력 과정 중 CPU 와 GPU 사이에서 하드웨어적으로 처리되고 있는 동기적 처리 과정을 소프트웨어적인 기법을 이용하여 비동기적으로 처리함으로써 성능을 향상시킬 수 있음을 말하고자 한다.
인체진동모델을 이용한 ER 시트 현가장치의 슬라이딩모드 제어
정진영(Jinyoung Jung),한영민(Youngmin Han),최승복(Seungbok Choi) 한국자동차공학회 2003 한국자동차공학회 춘 추계 학술대회 논문집 Vol.- No.-
This paper presents robust control performance of a semi-active ER(electro-rheological) seat suspension. A cylindrical type of ER seat damper is designed and manufactured for a commercial vehicle. The governing equation is derived from 6-DOF seat-driver model and the obtained seat-driver model is reduced through balanced model reduction. A sliding mode controller is then designed with full-order state observer and experimentally realized where a driver is sitting on controlled seat. Control performances are evaluated in both time and frequency domains. In addition, comparative work between ER seat suspension and conventional passive suspension is undertaken with ride quality criteria.
김성룡(Seong-Lyong Kim),이승재(SeungJae Lee),한영민(YoungMin Han) 한국추진공학회 2017 한국추진공학회 학술대회논문집 Vol.2017 No.5
고공엔진시험설비에서 지상 시험 조건의 시험 가능 여부와 설비 안전 문제를 점검하고자 로켓 엔진 유동을 해석하였다. 진공 챔버를 개방한 상태에서 냉각수를 초음속 디퓨저로 분사하면서 엔진이 작동하는 상황이며, 2차원 축대칭과 플룸, 공기, 냉각수의 3원 혼합물로 가정하였다. 해석 결과 냉각수 유량 200 kg/sec까지 지상 조건 시험이 가능하였다. 그러나 시동 초기 플룸의 역류로 인해 진공 챔버가 고온에 노출되고, 동시에 냉각수 역류로 인해 진공 챔버 내부가 오염되었다. 따라서 충분한 단열 대책과 오염 회피를 위한 작업이 선행되어야 한다. We analyzed the rocket engine flow to check whether the possibility of the ground test and the equipment safety problems in the high altitude engine test facility. The test condition is that the vacuum chamber is open and the coolant water is injected into the supersonic diffuser. The analysis uses two-dimensional axisymmetry with a mixture of plume, air, and cooling water. As a result, the ground test was possible up to the cooling water flow rate of 200 kg/sec. However, due to the back flow of the initial plume, the vacuum chamber is exposed to high temperature, and at the same time, the inside of the vacuum chamber is contaminated due to the reverse flow of the cooling water. Therefore, sufficient insulation measures and work for pollution avoidance should be preceded.
로켓엔진의 테스트스탠드 이송 및 장착 방안에 대한 사례연구
우성필(Seongphil Woo),김승한(Seunghan Kim),한영민(Youngmin Han) 한국추진공학회 2014 한국추진공학회 학술대회논문집 Vol.2014 No.12
로켓엔진은 높은 신뢰도를 확보하기 위해서 엔진 시스템의 성능시험평가가 필수적이다. 로켓엔진의 시험평가를 위하여 테스트스탠드에 이송 및 장착하는 방안에 대하여 해외사례를 조사하였고 국내에 구축중인 시험설비의 장착 방안에 대한 설계안을 소개하였다. Performance evaluation test is essential for the rocket engine in order to ensure a high reliability. Foreign cases of a rocket engine transfer and installation for tests was analyzed and the design results of the rocket engine installation method of test stand being built in Korea are described on this paper.