아기-알지네이트 연합 인상체의 보관방법 및 idophor 침적소독에 의한 체적 변화에 관한 연구

오남식,서정민,김선희,윤영아,심준성,Oh Nam-Sik,Seo Joung-Min,Kim Sun-Hee,Youn Young-Ah,Shim Joon-Sung 대한치과보철학회 2004 대한치과보철학회지 Vol.42 No.1

Statement of problem : Because dental impression can be a cross-infection source, disinfection, such as immersion disinfection is nessecary. However, the disinfection process may change the volume of the impression cast. Purpose : The purpose of this study is to find out the effects on dimensional change of different storage times and methods, of agar-alginate impression when immersed in a 5% idophor disinfectant. Material and Methods : An agar-alginate impression was made from a mandible model and then was disinfected and stored according the experimental conditions and a stone model was produced. Measurements were taken between reference points on the original mandible model and they were compared to measurements taken between reference points on the stone model. The study was divided into 4 groups. In group 1, the impression was stored in a 100% humidor for 30 minutes, 1 hour, 2 hours, 3 hours, 4 hours, 6 hours, 12 hours and 24 hours and stone models were made at each time. In group 2, the impression was immersed in 5% idophor disinfectant and then stored in a 100% humidor for the same length of times as group 1, and stone models were made at each time. In group 3, the impression was stored in extend-A-pourR, a special storage solution for 30 minutes, 1 hour, 2 hours, 3 hours, 4 hours, 6 hours, 12 hours, 24 hours 3 days, and 7 days and stone models were made at each time. In group 4, the impression was immersed in 5% idophor disinfectant and then stored in stored in extend-A-pourR, a special storage solution for the same length of times as group 3, and stone models were made at each time. 5 impressions and stone models were made at each time to make a total of 180. The Student-t test (P < .05) was used to do a statistical analysis of the measurements of the mandible model and stone models. The repeated-measure 2-way analysis of variance (P < .05) was used to do a statistical analysis of the difference in the 4 groups. Results : The percent liner dimensional change was from $0.25{\pm}0.03%$ (group 1, 30 minutes) to $0.34{\pm}0.06%$ (group 4, 7 days). No significant change was noticed between the 4 groups. Conclusion : According to the above study, in both methods, least dimensional change was recorded when the storage times were short and in both methods, immersion in 5% idophor disinfectant did not effect dimensional change in the agar-alginate impression.

최적설계기법을 이용한 완전도재 가공의치의 연결부 형태 보강

오남식,김한성,이명현,이근우,Oh Nam-Sik,Kim Han-Sung,Lee Myung-Hyun,Lee Keun-Woo 대한치과보철학회 2004 대한치과보철학회지 Vol.42 No.2

Statements of problem: All ceramic fixed partial denture cores can be made by the slip casting method and the advanced alumina tape method. The fracture resistance of these core connector areas is relatively low. Purpose: The purpose of this study is to standardize the appropriate volumetric figure and location of the connectors in the alumina core fabricated in alumina tape to be used in fixed partial dentures by way of topology optimization. Material and method: A maxillary anterior three-unit bridge alumina core with teeth form and surrounding periodontal apparatus model was used to ultimately design the most structurally rigid form of the connector. Loadings from a $0^{\circ}$, $45^{\circ}$ and $60^{\circ}$ to the axis of each tooth were applied and analyzed with the 3-D finite element analysis method. Using the results from these experiments, the topology optimization was applied and the optimal reinforcement layout of connector was obtained and the detail shape in the fixed partial denture core was designed. Results: The modified prosthesis with the form of a bulk in the lower lingual surface of the connector in the event, reduced the stress concentration up to 20% in the 3-D FEA. Conclusion: The formation of a bulk in the lower lingual connector area of an alumina core for a fixed partial denture decreases the stress to a clinically favorable measure but does not harm the esthetic point of view. This result illustrates the possibility of clinical application of the modified form designed by the topology optimization method.

알루미나 테이프를 사용한 유리 침투형 알루미나 코아의 변연적합도

오남식,이명현,김대준,이근우,이선형,Oh, Nam-Sik,Lee, Myung-Hyun,Kim, Dae-Joon,Lee, Keun-Woo,Lee, Sun-Hyeong 대한치과보철학회 1998 대한치과보철학회지 Vol.36 No.6

The purpose of this study was to compare the marginal fit of all ceramic crowns prepared from alumina slip casting, which is consistent with the conventional In-ceram system, and those fabricated from alumina tapes which is currently under development in an effort to alleviate complexities involved in the forming procedure of the In-ceram crown core. All ceramic crowns, made of In-ceram(slip casting) and alumina tapes(Doctor blade casting), were prepared with $90^{\circ}\;and\;135^{\circ}$ shoulder margins. The crowns were cemented with a glass ionomer cement and embeded in epoxy resin. The embedded crowns were sectioned faciolingually and mesiodistally and marginal discrepancies and marginal gaps were measured under the Measurescope MM II. The measurements were analyzed using Wilcoxon rank sum test and Kruskal-Wallis test and the results were as follows: 1. In the case of $90^{\circ}$ shoulder margin, the combined marginal discrepancies and marginal gaps were $78.3{\mu}m\;and\;44.4{\mu}m$ respectively, for the all ceramic crowns fabricated using the alumina tapes. In comparison, the values were $65{\mu}m\;and\;25.5{\mu}m$ for the In-ceram crowns. For the marginal gaps a statistical difference existed (p<0.05) but no significant difference was observed for the marginal discrepancy (p>0.05). 2. In the case of $135^{\circ}$ shoulder margin, the combined marginal discrepancy and marginal gaps were $82.1{\mu}m\;and\;40.2{\mu}m$ respectively, for the all ceramic crowns formed with the tapes. As compared with the marginal discrepancy and gaps of the $90^{\circ}$ shoulder margin in the fabricated from the alumina tapes, no significant statistical differencies were discerned in both cases (p>0.05). 3. There was no statistically significant difference in the fits among four locations around the margins of the all ceramic crowns fabricated using the alumina tapes. The results obtained in this study showed that the marginal fits of the glass infiltrated alumina cores fabricated from the alumina tapes are slightly higher value than those prepared using the In-ceram but the difference is within a clinically acceptable range.

해안지하수의 수위에 미치는 조석의 영향

박남식 ( Nam-sik Park ),오영훈 ( Young-hun Oh ),고병련 ( Byoung-ryoun Koh ) 한국환경기술학회 2014 한국환경기술학회지 Vol.15 No.6

본 연구는 해안지하수 적정관리 방안의 구축을 위해 제주와 같은 섬 지역에서 반드시 선행되어야 할 연구로 해안 및 도서 지역에서 해수침입은 해안지하수 확보 및 개발에 대한 심각한 요인으로 작용할 수 있다는 점에서 조석이 해안지하수의 지하수위에 미치는 영향을 분석하는데 있다. 연구대상지역으로 제주특별자치도에서 해수침입과 관련하여 자동관측하고 있는 제주성산유역의 수산관측공모니터링 자료를 분석하여 조석의 미치는 영향을 분석 하였다. 분석결과, 조석에 의한 지하수위, 수온, 전기전도도가 시간 별로 변화하고 있으며, 조석감쇄법으로 조석영향에 대한 반응시간을 제시하였다. This research is to be conducted in the island area like Jeju in order to establish the proper management method for coastal groundwater, and since the seawater intrusion in the coastal or island area can be the significant factor for the acquisition and development of coastal groundwater, it is to analyze the effect of tidal movement on the groundwater level. This research analyzed the relation between the groundwater level and the tidal movement based on the fishery peeping hole`s monitoring materials in Jeju-Sungsan area which the water resources headquarters of Jeju Island is observing automatically with respect to seawater intrusion. As a result, the groundwater level due to the tidal movement, the water=temperature and the electrical conductivity are changing by time, and according to the lag time calculated by the tidal damping method, the reaction time to the tidal influence is 1.43hr~ 3.68hr in average.

복합 레진에서 마무리 방법에 따른 표면 거칠기 비교

정숙인,오남식,이명현,이은정,조정현,지성원,Jeong, Suk-In,Oh, Nam-Sik,Lee, Myung-Hyeon,Lee, En-Jung,Cho, Jung-Hyeon,Ji, Sung-Won 대한치과보철학회 2008 대한치과보철학회지 Vol.46 No.2

전치부 영역에서의 복합 레진을 이용한 수복물의 표면은 착색과 치태 침착이 적어야 하며 치은 조직에 좋은 내성을 갖도록 평활해야 한다. 레진 수복 후 여러 마무리 방법중 blade를 이용한 방법은 치은과 접해있는 변연 부위의 불필요한 레진을 제거하고 마무리하는데 있어 치은 손상을 최소화하면서 간편하게 이용할 수 있는 방법이다. 본 연구의 목적은 현재 많이 사용되고 있는 nano-hybrid composite resin과 ormocer-based compostie resin 간의 여러 가지 마무리 방법에 있어 blade를 이용한 방법과 polishing을 시행한 경우의 표면 거칠기 및 nano계열과 ormocer 계열 복합 레진의 표면 특징을 비교하는 것으로 실험을 위해 가로 6mm, 세로 3mm, 높이 2mm의 금속 주형을 이용하여 레진 블록을 형성하고 대조군은 상면에 mylar strip을 위치시켜 광중합 하였으며, Ormocer - based composite resin ($Admira^{(R)}$)과 nanohybrid composite resin ($Grandio^{(R)}$)에서는 blade를 이용한 경우와 rubber polishing을 이용한 경우를 실험군으로 하였고, ormocer-based flowable composite resin ($Admira^{(R)}$ Flow)과 nanohybrid flowable composite resin ($Grandio^{(R)}$ Flow)에서는 blade를 이용한 경우, rubber polishing을 이용한 경우와 추가적으로 아무것도 시행하지 않은 경우를 실험군으로 하였다. 레진 블록의 표면은 profilometer 및 SEM을 이용하여 거칠기 및 조도를 비교하였으며 통계분석 하였다. 실험 결과 mylar stirp을 적용한 경우 Ra (${\mu}m$) 평균 값은 ormocer-base composite resin이 $0.25{\mu}m$, ormocer-based flowable resin $0.17{\mu}m$, nanohybrid composite resin $0.24{\mu}m$, nanohybrid flowable resin $0.18{\mu}m$ 였으며 blade를 적용한 경우 평균 값은 각각 $0.43{\mu}m$, $0.37{\mu}m$, $0.48{\mu}m$, $0.41{\mu}m$ 였다. 가장 낮은 Ra (${\mu}m$)은 mylar stirp을 적용한 시편에서 얻어졌으며, blade를 이용한 마무리 방법과 rubber polishing을 시행한 경우와 표면 거칠기 비교시 Ra (${\mu}m$)값에서 통계적으로 유의한 차이를 보이지 않았다 (P>0.05). Nanohybrid composite resin이 blade로 마무리하거나 rubber polishing후 ormocer-based composite resin보다 표면 거칠기 증가율이 좀 더 큰 것을 알 수 있었다. 이상의 결과는 blade를 이용한 마무리 방법이 다른 마무리 방법을 대체할 수 있을 것이라는 것을 보여주며, 이에 따라 본 실험 결과에 한정지어 볼 때 복합레진 수복후 마무리 방법으로 blade를 이용하여 시행하는 것이 적용가능 할 것이라 생각된다. Statement of problem: Proper finishing and polishing enhance both the esthetics and the longevity of restored teeth. Blade finishing technique would be suited for smoothing and finishing. Evaluation of this technique are necessary. Purpose: The purpose of this study was to evaluate the blade finishing and polishing procedures on the surface profile and roughness of ormocer-based composite resin and nanohybrid composite resin. Material and methods: The material included a ormocer-based composite resin ($Admira^{(R)}$ & $Admira^{(R)}$ Flow); a nanohybrid composite resin ($Grandio^{(R)}$ & $Grandio^{(R)}$ Flow). One hundred forty specimens of each group were prepared using a mylar strip and randomly divied into blade finishing and rubber polishing groups (n=10). The average surface roughness (Ra) in micrometers was measured and the surface profile was examined by scanning electron microscopy (SEM) (Magnification ${\times}$ 200). The data were analyzed by Mann-Whitney Test at 0.05 significance level. Conclusion: The results of this study indicated that the mylar strip produced the smoothest surface on all materials and among the finishing-polishing methods was not significanct difference (P>0.05). Ormocer-based flowable composite resin performedthe lowest variability in initial surface roughness among the tested materials.

강화형 글라스 아이오노머 합착용 시멘트의 접합강도 및 변연누출에 대한 연구

박혜양,오남식,이근우,이호용,Park, Hye-Yang,Oh, Nam-Sik,Lee, Keun-Woo,Lee, Ho-Yong 대한치과보철학회 1997 대한치과보철학회지 Vol.35 No.4

The resin modified glass ionomer cements(RMGICs) have been used for years since 1989. Recently it has been developed for luting of fixed restorations. To evaluate the bond strength and marginal leakage of RMGICs for luting usage, the 80 extracted human molars which had uniform area of exposed dentin were cemented with 3 types of RMGICs(Fuji Duet, Advance, Vitremer), a conventional Glass Ionomer Cement(GIC-Fuji I), and a resin cement (Panavia 21) to base metal alloy(Ni-Cr-Be). After thermocycling the specimens were immersed in basic fuschin dye for measuring marginal leakage. The shear bond strength was measured with Instron and the maximum dye penetration was measured to 0.1mm. The types of fractured patterns were determined with stereoscope(${\times}7.5$). The results are as follows. 1. The difference between 3 RMGICs and a conventional GIC in shear bond strength was not statistically significant. It seemed that RMGICs had lower shear bond strength than resin cement. (p<0.01) 2. The mean scores of marginal leakage had no significant difference between the resin cement and 3 RMGICs but it was much higher in conventional GIC than the RMGICs (p<0.05) 3. It was determined that the manufacturer and the methods of dentin pretreatment determined the pattern of fracture surfaces and the frequency of adhesive failure between teeth and 3 RMGICs standed as in following order - Vitremer, Advance, Fuji Duet. (p<0. 01) When the fracture pattern was analyzed, it could be said that the materials and the method of dentin pretreatment have much effect on bonding states. This means that the dentin bonding agents should be improved. But the limited products in this experiment can not evaluate the physical properties of the entire RMGICs. Therefore a further study which can evaluate various RMGICs should be in progress to develope better cements.

상아질 지각완화제가 치과용 시멘트의 결합강도에 미치는 영향

나윤호,오남식,유재흥,Na, Yun-Ho,Oh, Nam-Sik,Yoo, Jae-Heung 대한치과보철학회 2007 대한치과보철학회지 Vol.45 No.5

Statement of problem: A tenderness of the dentin after tapering of teeth for dental prosthesis is a common phenomenon. In practice, the alternative desensitizer may be used for minor pain after tapering of teeth. Purpose: In this study, the desensitizers were used to investigate the affect decreasing of shear bond strength according to the use of various cement, such as resin, Glass Ionomer, and phosphate cement. Material and method: Three different desensitizers were used on this study Compositions of two dentin desensitizers were HEMA(hydroxyethylmethacrylate) and glutaraldehyde. The other one is oxalic acid. Three dentin desensitizers applied on 12 degrees taper teeth. Then, Ni-Cr crowns were bonded with Resin cement, Zinc Phosphate (ZPC) cement and Glass Ionomer (GIC) cement. 120 human premolar teeth were used for specimens. The specimens were divided into four group as the reference and the empirical each with thirty specimens, then further divided into 12 group according to type of desensitizers and cement types. The shear bond strength were measured by Instron multi task instrument. Results: According to the result, the measured shear bond strength in order from the weakest to the strongest in general was ZPC, Resin, and GIC. And it is found that the application of desensitizers on dentin surface does not affect the shear bond strength. Conclusion: Dentin desensitizers that alleviate or prevent a dentin tenderness, usually contains HEMA and glutaraldehyde compounds. Such desensitizers are widely used in clinical studies. By applying the dentin desensitizer on the exposed dentin surface, the dentin capillary are blocked and periodontal membrane and cementum can not be drawn in pulp cavity. Since HEMA and glutaraldehyde may cause harm to the pulp cavity, an alternative desensitizer was developed.

임시 수복물 중합시 시간과 중합온도가 변연 적합도에 미치는 효과

윤승환,오남식,김일규,오성섭,최진호,김왕식,임영일,Youn Seung-Hwan,Oh Nam-Sik,Kim Il-Kyu,Oh Sung-Seop,Choi Jin-Ho,Kim Wang-Sik,Rim Young-Il 대한치과보철학회 2001 대한치과보철학회지 Vol.39 No.5

The purpose of this study was to compare the marginal fit of provisional restorations by differentiating the removal time and setting temperature during resin polymerization. After mixing autopolymerizing methyl methacrylate resin, the material was placed in a preformed resin shell crown. The crown was seated on a die with 1mm shoulder margin. Crowns were removed after 3, 4, 5, 6 minutes and polymerization was continued under the following conditions : $25^{\circ}C$ air, $30^{\circ}C,\;40^{\circ}C,\;50^{\circ}C,\;60^{\circ}C,\;70^{\circ}C$ water. After polymerization. the crown was sectioned. The marginal & occlusal discrepancies were measured. The mean marginal discrelpancies at 3 minutes, 4 minutes, 5 minutes and 6 minutes of removing time were $96.6{\mu}m.\;84.6{\mu}m,\;86.7{\mu}m$ and $105.6{\mu}m$. The mean occlusal discrepancies at 3 minutes, 4 minutes, 5 minutes and 6 minutes of removing time were $106.7{\mu}m,\;89.3{\mu}m,\;98.6{\mu}m$ and $127.7{\mu}m$. There was significant difference between 4 minutes group and 6 minutes group in occlusal discrepancies. The mean marginal & occlusal discrepancies for crowns polymerized in $25^{\circ}C$ air were $98.2{\mu}m$ and $124.1{\mu}m$. The crowns polymerized in $50^{\circ}C$ water demonstrated the smallest marginal & occlusal. discrepancies. The mean value of marginal & occlusal discrepancies in $50^{\circ}C$ water were $73.1{\mu}m$ and $77.5{\mu}m$. These values were smaller than that of $25^{\circ}C$ air. There were significant differences in the occlusal discrepancies between $25^{\circ}C$ air and water conditions of $50^{\circ}C$ water (${\alpha}=0.05$) but. no significant difference in marginal discrepancies. There was no significant difference in the interaction between time and temperature. 4 minutes waiting time & $50^{\circ}C$ water polymerizing condition produces the best fit at the margin of the provisional crown.

제왕절개술에서 경식도 초음파를 이용한 폐혈전색전증의 수술 중 진단

오충식 ( Choong Sik Oh ),곽상원 ( Sang Won Kwak ),김태엽 ( Tae Yop Kim ),우남식 ( Nam Sik Woo ),손인숙 ( In Sook Sohn ),지현근 ( Hyun Keun Chee ) 대한마취과학회 2008 Korean Journal of Anesthesiology Vol.54 No.1

치주 지지가 감소된 소구치에서 포스트가 치근 응력 분포에 미치는 영향에 대한 3차원 유한요소법적 연구

정혜진,유재흥,오남식,김한성,Jeong, Hye-Jin,Yoo, Jae-Heung,Oh, Nam-Sik,Kim, Han-Sung 대한치과보철학회 2007 대한치과보철학회지 Vol.45 No.5

Statement of problem: The endodontically treated tooth is generally restored with post and core, owing to the brittle and the loss of large amount of tooth structure. As periodontal treatment was developed, there are many cases that periodontally involved teeth used in prosthetic treatment. Purpose: The purpose of this study was to analyze the stress distribution in the dentin and post structures by the various post materials and the amount of remaining alveolar bone height. Material and method: The 3-dimensional finite element models of mandible 1st premolars were divided into six types according to the various amount of remaining alveolar bone and post type. All types were modeled using equal length, diameter and shape of the post. Three types of post and core materials were used: prefabricated titaniumpost and amalgam core, prefabricated stainless steel post and amalgam core, and cast gold post and core. 300 Newton force was applied to functional cusp of mandible 1st premolar. Results: The results were as follows: First, there was no apparent difference in the pattern of stress distribution according to the alveolar bone condition concentrate on the post middle area. Second, there was difference in pattern of stress distribution according to the core materials, gold post and core generated same than amalgam core. Third, there was no apparent difference in the pattern of stress distribution within the dentin according to the post and core materials. But a cast gold post and core generated the lowest maximum stress value, a stainless steel post generated the highest maximum stress value. Fourth, in the reduced alveolar bone model, maximum stress value is 1.5 times than that of the normal alveolar bone model. Conclusion: Within the limitations of this study, to provide minimal stress to the root with alveolar bone reduced, the post length may be as long as apical seal was not destroyed. To prevent fracture of tooth, it is rational to use gold alloy which material was good for stress distribution for post materials.