http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
안태상,김영주,김형근,장동운,최경규,김종락,Ahn, Tae Sang,Kim, Young Ju,Kim, Hyung Geun,Jang, Dong Woon,Choi, Kyoung Kyu,Kim, Jong Rak 한국강구조학회 2013 韓國鋼構造學會 論文集 Vol.25 No.1
기존 내진설계의 목적은 구조물의 갑작스런 피해로 인한 인명손실을 방지하는 것이다. 지난 수십년간 구조물의 내진성능을 향상시키기 위해서 효과적인 지진저항시스템을 개발하는 수많은 연구들이 진행되었다. 본 연구의 목적은 내진성능을 향상시킴과 동시에 지진 이후 보수가 편리하도록 하는 새로운 제진시스템을 제안하는데 있다. 제안된 제진시스템은 벽의 하부에 슬릿을 두고 제진장치가 수평으로 작동하도록 하여 지진에너지를 소산하도록 계획되었다. 제안된 시스템의 이력거동과 에너지소산능력을 조사하기 위해서 반복가력실험을 실시하였다. 실험결과는 제안된 시스템이 안정된 이력응답을 나타내며, 에너지의 소산은 제진장치에 집중되는 것을 보여준다. The objective of conventional seismic design is to ensure an acceptable safety level while avoiding catastrophic failures of structures and loss of life. Over the last many years, a large amount of research has been devoted into developing effective earthquake resistant systems in order to raise the seismic performance level of structures. The purpose of this study is to propose a new damping system, which realize not only increasing seismic performance but also easy repairing after an earthquake. The proposed damping system is slit in the bottom of wall with damping devices installed in the slit horizontally aiming to dissipate energy during earthquakes. Cyclic loading tests were conducted to investigate hysteretic behavior and energy dissipation capacity. Test results show that the proposed systems exhibit a stable hysteretic response and the energy dissipation in this system is concentrated on the damping devices.
안태상,김영주,박진화,김형근,장동운,오상훈,Ahn, Tae-Sang,Kim, Young-Ju,Park, Jin-Hwa,Kim, Hyung-Geun,Jang, Dong-Woon,Oh, Sang-Hoon 한국강구조학회 2012 韓國鋼構造學會 論文集 Vol.24 No.2
최근에 신축 건물이나 기존 건물의 내진보강을 위해서 수동제진장치의 일종인 에너지소산형 제진장치의 사용이 매우 증가하고 있다. 제진장치는 선진국을 중심으로 개발되어 왔고 제한적으로 사용해 오고 있었지만, 최근에는 다소 저렴한 장치개발을 통하여 강진지역의 개발도상국으로도 그 사용이 확대되고 있다. 본 연구는 기존 또는 신축 건물의 내진보강을 위한 캔틸레버타입 강재댐퍼를 개발하고 제안하였다. 댐퍼에 대한 반복가력 실험을 바탕으로 이력거동 및 에너지소산능력을 조사하였다. 실험결과는 제진장치가 안정된 이력특성을 나타내고 있으며 큰 에너지소산능력을 갖고 있음을 보여준다. 실험결과를 바탕으로 댐퍼에 대한 간단한 하중-변위 이력모델을 제안하였다. The use of seismic energy-dissipative devices for passive control is increasing exponentially in the recent years for both new and existing buildings. Use of these devices started in and has been somewhat limited to developed countries. One of the current challenges is to promote the use of seismic dampers in earthquake-prone developing countries by lowering the cost of the devices. This paper proposed a new type of seismic damper based on yielding of a cantilever type metallic element for seismic retrofit of existing and new building structures. The hysteretic behavior and energy dissipation capacity of the proposed damper was investigated using component tests under cyclic loads. The experimental results indicated that the damping device had stable restoring force characteristics and a high energy dissipation capacity. Based on these results, a simple hysteretic model for predicting the load-displacement curve of the seismic damper was proposed.
본진의 크기와 여진을 고려한 전단벽 제진시스템에 관한 실험적 연구
안태상(Ahn, Tae-Sang),김영주(Kim Young-Ju),김형근(Kim Hyung-Geun),장동운(Jang Dong-Woon),오상훈(Oh Sang-Hoon),김종락(Kim Jong-Rak) 대한건축학회 2012 大韓建築學會論文集 : 構造系 Vol.28 No.8
A new damping shear wall system is proposed to improve the seismic performance of building structures. A steel damper in the proposed damping system is installed in the bottom slit horizontally of the shear wall aiming to dissipate energy during earthquakes and prevent damage of the structure, which could not only provide good seismic performance but could also easily repaired after an earthquake. The main feature of this system is that plastic deformation is limited to the steel dampers at the bottom of walls. The seismic performance of the proposed damping system was verified through cyclic tests of seven full-scale wall structures that had steel dampers. Tests were conducted to simulate the effect of aftershocks which can cause additional damage to already weakened structures after an earthquake. Based on the test results, the cyclic performance of damping shear wall systems was discussed with emphasis on the energy dissipation capacity.
합성보에 적용된 앵글 전단연결재의 Push-out 실험
김영주,배재훈,안태상,장동운,Kim, Young Ju,Bae, Jae Hoon,Ahn, Tae Sang,Jang, Dong Woon 한국강구조학회 2014 韓國鋼構造學會 論文集 Vol.26 No.3
강-콘크리트 합성보는 오랫동안 건물시공에 사용되어져 왔다. 합성보의 필수요소는 강재단면과 콘크리트 슬래브 사이의 전단접합이며, 주로 기계적 전단연결재가 사용되며 다양한 형상의 장치가 사용되어져 왔다. 본 연구는 앵글 전단연결재를 가진 push-out 실험체의 실험결과를 조사한 것이다. 앵글 전단연결재의 전단성능을 검토하기 위해서 모두 22개의 push-out 실험체를 설계하였으며, 앵글의 높이, 용접길이 및 앵글의 간격 등의 실험변수를 바탕으로 그 영향을 검토하였다. 실험결과를 바탕으로 앵글 전단연결재의 전단강도를 예측할 수 있는 설계식을 제안하였다. Steel-concrete composite beam has been used for a considerable time in building construction. An essential component of a composite beam is the shear connection between the steel section and the concrete slabs, which is provided by mechanical shear connectors. A variety of shapes and devices have been in use as shear connectors. This study summarizes the results of an experimental investigation involving the testing of push-out specimens with angle shear connectors. All of 22 push-out specimens were designed to study the effect of a number of parameters on the shear capacity of angle shear connectors such as the height of the angle connector, the length of welding, and the pitch of angles. Based on the test results, a design equation was developed for predicting the shear strength of angle shear connectors.