http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
방희선,방한서,김유철,주성민,좌순원,노찬승,Bang, Hee-Seon,Bang, Han-Sur,Kim, You-Chul,Joo, Sung-Min,Joa, Soon-Won,Ro, Chan-Seoung The Korean Welding and Joining Society 2009 대한용접·접합학회지 Vol.27 No.5
Thermal and mechanical characteristics in dissimilar SS400-STS304 steel weldment have been investigated by 3D thermal elastic-plastic analysis. Moreover, the influence of welding residual stresses on the mechanical behaviour of this welded joint, by applying superimposed external load (tension load) was determined. The residual stresses obtained by numerical simulation were compared with the experimentally measured results. The FE results were in good agreement with the measured values. The mechanical test (hardness, tensile test) and metallurgical analysis was carried out to ensure the weld integrity. Hence, possibility of applying SS400-STS304 dissimilar steels in industries has been established.
Analysis of Residual Stress on Dissimilar Butt Joint by TIG Assisted Hybrid Friction Stir Welding
방희선,노찬승,엠 에스 비조이,방한서,이윤기,Bang, Hee-Seon,Ro, Chan-Seoung,Bijoy, M.S.,Bang, Han-Sur,Lee, Yoon-Ki The Korean Welding and Joining Society 2012 대한용접·접합학회지 Vol.30 No.2
This paper aimed to study and understand the mechanical phenomena of thermal elasto-plastic behavior on the dissimilar butt joint (Al 6061-T6 and STS304) by TIG assisted Friction Stir Welding. Heat conduction and residual stress analysis is carried out using in-house solver. Two-dimensional results of the heat distribution and residual stresses in dissimilar joint for particular tool geometry and material properties are presented. The predicted stress along longitudinal direction in Al 6061-T6 and STS304 are approximately between 12-15% of their respective yield strengths. A comparison is made between experimentally measured and numerically predicted equivalent residual stress values.
노치가공에 의한 다층 FCA 용접부의 잔류응력 재분포 특성
방희선,방한서,오익현,김준형,Bang, Hee-Seon,Bang, Han-Sur,Oh, Ik-Hyun,Kim, Jun-Hyung 대한용접접합학회 2010 대한용접·접합학회지 Vol.28 No.1
In the present study, two-dimensional plane deformation thermo elasto-plastic analysis has been carried out, in order to investigate the thermal and mechanical behaviour (residual stress, plastic strain, magnitude of stress and their distribution and production mechanism) on multi-pass FCA butt weldment of high strength EH36-TMCP ultra thick plate. Moreover, this study can be considered as a basis for analysing the fracture toughness, KIC, and its effect on welding residual stress redistribution with notch on multi-pass FCA butt weldment, in future. The results of welding residual stress obtained from thermo elasto-plastic analysis has been compared and verified with the results measured by XRD.
고강도 극후판 EH36-TMCP강 EGW용접부의 역학적 거동 및 파괴인성 $K_{IC}$에 관한 해석
방희선,방한서,주성민,Bang, Hee-Seon,Bang, Han-Sur,Joo, Sung-Min 한국전산구조공학회 2009 한국전산구조공학회논문집 Vol.22 No.6
본 연구에서는 EGW공정 적용에 따른 고강도 극후판 EH36-TMCP강 용접부의 역학적 거동 및 파괴인성 $K_{IC}$ 특성을 고찰하기 위해 먼저 자체 개발한 열분포, 열탄소성 프로그램을 이용한 유한요소해석을 통하여 용접부의 역학적 거동(용접잔류응력, 소성변형율 등의 크기, 분포, 발생기구)을 규명하였다. 그리고 이때 얻어진 잔류응력을 초기응력으로 하여 상용프로그램 ANSYS에서 노치가공으로 인한 응력 재분포 특성 및 잔류응력과 외력의 복합하중에 대한 파괴인성 KIC를 계산하였다. 균열이 존재하는 EGW용접부의 파괴기준$K_{IC}$를 살펴보면, 중첩된 경우가 순수 외부하중(굽힘하중)만 작용하는 경우 보다 파괴 인성치가 다소 감소하는 경향을 보였다. a/W가 작을 경우 중첩의 경우가 순수 외부하중(굽힘하중)만의 경우보다 파괴인성치 차이가 크나, a/W가 증가함에 따라 그 차이가 점차 없어지는 것으로 나타났다. This work intends to establish the reliability and fracture toughness $K_{IC}$ criterion of welded joints by EGW for high strength EH36-TMCP ultra thick plate. For this, firstly thermo elasto-plastic analysis has been carried out on two pass X-groove butt joint model to clarify the thermal and mechanical behaviour(residual stress, plastic strain, magnitude of stress and their distribution and production mechanism). Moreover, to establish fracture criterion, analysis of fracture toughness $K_{IC}$ has been performed under the notch machined and residual stress with the load condition on EGW welded joints. A quantitative fracture criterion for EGW welded joints is suggested by using $K_{IC}$.
고속가스플래임 용사법을 이용한 광촉매 $TiO_2$-생분해성 플라스틱 복합재료의 개발
방희선,방한서,Bang, Hee-Seon,Bang, Han-Sur,Ohmori, Akira 대한용접접합학회 2006 대한용접·접합학회지 Vol.24 No.5
For the production of functional $TiO_2$-biodegradable plastic (polybutylene succinate:PBS) composite material with photocayalytic activity, we attempted to prepare $TiO_2$ coatings on PBS substrate by HVOF and plasma spraying techniques under various conditions. The microstructures of coatings were characterized with SEM and XRD analysis, and the photocatalytic efficiency of coatings was evaluated by the photo degradation of gaseous acetaldehyde. The effects of primary particle size and spraying parameters on the formation behavior, photocatalytic performance of the coatings have been investigated. The results indicated that for both the HVOF sprayed $P_{200}$ and $P_{30}$ coatings, the high anatase ratio of 100% can be achieved regardless of fuel gas pressure. On the other hand, the HVOF sprayed $P_7$ coating exhibited a largely decreased anatase ratio (from 100% to 49.1%) with increasing the fuel gas pressure, which may be attributed to much higher susceptibility of heat for 7 nm agglomerated powder. HVOF sprayed $P_{200}$ and $P_{30}$ coatings show better performance as compared to that of plasma sprayed $P_{200}$ coatings owing to the higher anatase ratio. However, the HVOF sprayed $P_7$ coatings did not show the photocatalytic activity, which may result from the extremely small reaction surface area to the photocatalytic activity and low anatase ratio.
Temperature Behavior in Dissimilar Butt Joint During TIG Assisted Friction Stir Welding
방희선,엠 에스 엠조이,Bang, Hee-Seon,Bijoy, M.S. The Korean Welding and Joining Society 2011 대한용접·접합학회지 Vol.29 No.5
Three-dimensional finite element analysis is performed to study the temperature distribution phenomenon of TIG assisted friction stir welding (TAFSW) between dissimilar plates (Al 6061-T6 and stainless steel 304). TAFSW is a solid-state welding process that integrates TIG (Tungsten Inert Gas) into a friction stir welding (FSW), to preheat the harder material ahead of FSW tool during welding. In order to facilitate the industrial application of welding, 3D numerical modeling of heat transfer has been carried out applying Finite Element Method (FEM). The temperature distribution due to heat generation during TAFSW on dissimilar materials joint is analysed using in-house solver. Moving heat source along with frictional heat between the work specimens and tool surface is considered to calculate the heat input. The analytical model used predicts successfully the maximum welding temperatures that occur on the dissimilar materials during TAFSW. Comparison with the infra red camera and thermocouple measurement results shows that the results from the current numerical simulation have good agreement with the measured data.
판례평석(判例評釋) : 영업사원의 시장유통가격 판매행위와 업무상 배임죄의 문제 -대법원 2009. 12. 24. 선고 2008도4590 판결-
방희선 ( Hee Seon Bang ) 법조협회 2011 法曹 Vol.60 No.1
배임죄는 타인의 사무를 처리하는 자가 자신의 사리를 위하여 임무에 반하는 행위로 본인에게 손해를 가하는 범죄로 풀이된다. 그런 면에서 범죄의 본질을 임무(신뢰관계) 위배로 보고 그로 인한 손해발생을 핵심으로 보는 입장이 실무관행과 해석론의 일반적 경향이었다. 따라서 형법규정상의 이득부분은 추상적 위험 정도로 형식적 해석에 그친 편인데, 이는 종래 우리와는 규정 형식이 다소 다른 독일과 일본 형법의 해석론을 기초로 해 온 데 따른 것으로 보인다. 그런데 최근 우리 법원은 그러한 종래의 관행을 벗어나 이득에 대한 객관적이고 구체적인 내용을 요구하는 새로운 입장을 제시하고 있다. 임무위배 행위와 손해 발생을 핵심으로 보고, 이득 부분은 관념적인 추상적 위험 정도로 보아 오던 방식을 버리고 모두 동일한 차원의 구체화된 실제적 내용을 추구하려는 것으로 보인다. 따라서 관련사례를 통하여 죄형법정주의에 보다 충실한 새로운 해석 기준과 내용을 분석, 정리해 보고자 한다.
방희선(Bang Hee-Seon) 한국법학원 2009 저스티스 Vol.- No.110
수사단계에서 유력한 증거를 미리 확보하여 공판심리에 활용할 수 있도록 마련된 절차로서 증거보전청구제도가 있다. 이는 특히 증거자료 수집에 필요한 강제처분권 등 아무런 활용수단이 없는 피의자, 피고인에게 유용한 절차로서 실질적 방어권 보장을 통한 당사자주의 소송구조의 표현이라 할 수 있다. 그런데 이러한 증거보전절차에 현행 제도의 구체적 내용과 관련해서는 여러 견해와 대립이 있고 입법론상 개선의 여지가 지적되기도 한다. 따라서 그 시기적 범위와 절차 대상, 불복방안에 대한 주요 논의를 살펴보고, 특히 최근 이루어진 형사소송법의 부분적 개정에 따른 관련 해석문제 등도 비교 검토할 필요가 있다. 또한 형사소송법 제221조의 2 소정의 증인신문청구제도와의 균형상 현행 제도가 타당한 것인지, 나아가 최근 검찰이 제기하고 있는 참고인 구인제도의 주장과도 연관된 차원에서 음미할 필요가 있다고 본다. 이를 위해 本稿에서는 증거보전제도의 취지와 성격, 내용 등을 규명하면서 그에 관한 여러 견해와 판례의 태도 등을 검토하고자 한다. 아울러 이 제도의 개선을 위한 입법론을 살펴 보고 최근 개정으로 도입된 불복방법인 항고 절차의 문제점도 함께 짚어 보고자 한다. Korean Criminal Procedure Act prescribes the preservation of evidence by court, which renders both parties(defendant/prosecutor) the opportunity of obtaining the essential evidences in advance of trial sessions. It is particularly important for the defendants since they don’t have proper means to search and obtain favorable evidences for themselves during investigation stage. So, we need to study this institution more closely and to check out related problems and weaknesses. And moreover, the appellate procedure, in case of rejection for petition of injunctive measures, is quite problematic in relation to the partial amendment of penal code in recent years. To solve such problems and questions, the relevant authentic commentaries, authoritative theories and related case rulings shall be examined in coordination. In addition, another necessary amendments of the Act shall have to be urged for reasonable rearrangement of such questions and procedural problems.