http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
박태춘(Tae Choon Park),한정엽(Jung-Youp Han),강신형(Shin-Hyoung Kang) 한국유체기계학회 2007 유체기계 연구개발 발표회 논문집 Vol.- No.-
A study on the flow characteristics of a core flow and the behavior of a rotating stall at the third stage rotor- and stator-row exits of a 4-stage low speed axial compressor was experimentally performed to investigate its performance and instability of the compression system. The pressure losses generated due to the leakage flow at a tip clearance and a shroud seal clearance and the wake flow near the trailing edge of a blade were taken into consideration to estimate the causes of performance drop of the low speed research compressor in Seoul National University, compared with that in General Electric Aircraft Engine. In addition, the measurement of rotating stall was conducted from hot-wire signal analysis and the existence and behavior of stall cell could be confirmed from FFT and cross-correlation.
박태춘(Tae Choon Park),강영석(Young-Seok Kang),양수석(Soo Seok Yang),이진근(Jinkun Lee) 한국항공우주연구원 2009 항공우주기술 Vol.8 No.1
5㎿급 발전용 가스터빈을 개발하기 위해 주요 구성품 중의 하나인 압축기의 성능을 시험 평가하고자 하며, 이를 위한 사전 작업으로 압축기 시험 리그의 진동 특성을 분석하여 압축기 운전시 구동 방법에 대한 정보를 확보하였다. 압축기 시험 설비는 입?출구 배관과 시험부 및 구동부로 구성되어 있고, 특히 구동부와 시험부에서 가속도계를 이용하여 진동 특성을 계측하였다. 압축기 주 하우징과 콜렉터, 베어링캐리어, 토크미터, 기어박스, 전동 모터 등에 가속도계를 장착하여 진동 속도 및 주파수 분석을 수행하였다. Vibration analysis of a turbo compressor test rig was carried out in order to investigate the vibrational characteristics of the compressor facility in KARI before conducting the compressor performance test of 5㎿-class gas turbine engine for generation. The overall compressor test facility consists largely of inlet and exit ducts, a test section and a driving part. Vibration was measured with accelerometers at the test section and the driving part, especially at a main housing, a collector, a bearing carrier, a torquemeter, a gearbox, and an electric motor. Gap sensors are also installed to measure the rotordynamic characteristics of compressor shaft.
박태춘(Tae Choon Park),강영석(Young-Seok Kang),양수석(Soo Seok Yang) 한국항공우주연구원 2008 항공우주기술 Vol.7 No.2
5㎿급 발전용 가스터빈의 주요 구성품 중 압축기에서의 성능시험 및 해석을 위해 측정 파라미터와 그 파라미터를 계측하기 위한 센서류를 선정하고자 한다. 축류압축기의 경우 각 단의 케이싱에서 정압 분포를 평균하여 계측하고, 내부 유동장에서 Kjel 온도관을 이용하여 전압 및 전온도 분포를 계측한다. 원심압축기의 경우 임펠러 출구의 허브면과 팁면에서의 정압 분포는 일반적으로 상당한 차이가 존재하므로 각 면에서 정압을 측정하여 평균하고, 디퓨저 내부와 디스월러 내부에서의 정압 분포를 계측하기 위해 한 피치에서 5개의 유선을 따라 10 곳에서 정압을 측정하고자 한다. 또한 압축기 내 유동특성과 동익-정익간의 상호작용을 고찰하기 위해 5공 피토관을 이용하여 내부 상세유동을 계측한다. The instrumentation was studied in order to measure aerodynamic performance and efficiency of a compressor as a component of a 5㎿-class gas turbine for power generation. In case of an axial compressor, the distributions of static pressure on a casing can be obtained by averaging at each stage and those of total pressure and temperature in the flow field of the compressor can be measured with a Kiel temperature probe. In case of a centrifugal compressor, the static pressures at the hub and the tip, respectively, of an impeller exit are considerably different, so the pressures need to be measured at both positions and thereafter averaged. The distributions of static pressures in a diffuser and a deswirler are measured at ten positions along five streamlines in one pitch. In addition, the flow field can be measured in detail by 5-hole Pitot tube in order to analyze the flow characteristics of the core flow region and wake region and the rotor-stator interaction of the compressor.