중·저준위 방사성폐기물 고화체의 압축강도 평가를 위한 초음파속도 측정

문균영,이태훈,문용식,Moon, Gyoon Young,Lee, Tae Hun,Moon, Yong Sig 한국압력기기공학회 2011 한국압력기기공학회 논문집 Vol.7 No.4

In order to ship low & Intermediate level radioactive waste drums, which have been temporarily stored on site, to a disposal facility, their physical and chemical properties should be evaluated and proven to meet the acceptance guideline prior to their shipment. Ultrasonic velocity method, which has been used to estimate the strength of concrete, can be suggested to evaluate the compressive strength of solidified radioactive waste, which is one of the evaluated properties. The strength is estimated from acoustic velocity. However, a guided wave traveling along a drum is generated when applying ultrasonic method to the drum, and this makes it difficult to analyze the signal due to overlap between transmitted wave through the contents in drum and the guided wave. This paper reported feasibility of ultrasonic method to evaluate of the compressive strength of the solidified LLW. It is observed that the guide wave is greater than transmitted wave, and ultrasonic velocity could be estimated from transmitted wave signal arriving prior to the guided wave

원전 증기발생기 와전류검사 시스템 현장적용 연구

문균영,이태훈,김인철,Moon, Gyoon-Young,Lee, Tae-Hun,Kim, In-Chul 한국압력기기공학회 2015 한국압력기기공학회 논문집 Vol.11 No.2

Steam generator is one of the most important component of nuclear power plant, and it's integrity and reliability are to be assured to high level by pre-service inspection and in-service inspection. To improve the reliability of steam generator heat exchanger tubes and to secure the management of nuclear power plant safely, KHNP CRI recently has developed eddy current testing system for steam generator. KHNP CRI have performed a series of experimental verification and field application to confirm the performance of the developed ECT system in accordance with ASME Code requirements. The ECT system consists of a remote data acquisition unit, an ECT signal acquisition and analysis software, a water chamber robot controller and a probe push-puller. In this paper, we will details of the developed ECT system and the software and their experimental performance. And also we will report the field applying performance and the issues for further steps.

원전 증기발생기 와전류검사 시스템 개발

문균영,조찬희,유현주,이태훈,조용배,Moon, Gyoon-Young,Cho, Chan-Hee,Yoo, Hyun-Joo,Lee, Tae-Hun,Cho, Yong-Bae 한국압력기기공학회 2013 한국압력기기공학회 논문집 Vol.9 No.1

The capacity factor of nuclear power plant in Korea is the highest level in the world. However, the integrity assessment of nuclear power plant is depended on foreign country. Especially, most eddy current testing systems for inspecting steam generators in nuclear power plant are currently imported from USA, Canada, and so on. Therefore, the eddy current testing system can react more active and adaptive from economic and managerial standpoint for actual nuclear power plants in Korea is required. In this paper, an eddy current testing system for inspecting steam generators in nuclear power plants is introduced. Frequency generator, analog circuit, analog digital converter circuit, and digital control circuit are composed in eddy current testing system. A benchmarking of acquisition system and acquisition software, eddynet 11i made by Zetec, and modifications are carried out based on the test environment of Korea nuclear power plants. Finally, all eddy current apparatus are integrated to inspect steam generator tubes in nuclear power plants.

원전 방진기 검사 및 관리 현황

조용배,문균영,유현주,Cho, Yong-Bae,Moon, Gyoon-young,Yoo, Hyun-Joo 한국압력기기공학회 2014 한국압력기기공학회 논문집 Vol.10 No.1

Recently, it is getting more and more important ensuring the integrity for the equipment degradation according to the increase of nuclear power plant operating period. In many equipment of the nuclear power plant, snubbers mainly installed in reactor coolant pumps, steam generators and piping protected the equipment and piping from the occurrence of transient dynamic loads such as the earthquake, thermal load during the plant operation. This report describes the function, regulation, inspection requirements and management status of the snubbers installed in domestic nuclear power plants.

한울 3호기 주급수 배관 용접부 육안검사 경험

윤병식,문균영,김용식,Yoon, Byung Sik,Moon, Gyoon Young,Kim, Yong Sik 한국압력기기공학회 2015 한국압력기기공학회 논문집 Vol.11 No.1

Nuclear power plant steam generator that is one of the main component has several thousands of thin tubes. And the steam generator tube is subject to damage because of the severe operation conditions such as the high temperature and pressure. Therefore periodic inspections are conducted to ensure the integrity of steam generator component. Hanul unit 3 also has been inspected in accordance with in-service inspection program and is scheduled to be replaced for exceeding the plugging rate which was recommended by manufacturer. During the steam generator replacement activity, we found several clustered porosity on inner surface of main feed water pipe. Additionally crack-like indications were found at weld interface between base material and weld of main feed water pipe. This paper describes the field experience and visual testing results for inner surface of main feed water pipes. The destructive test result had shown that these indications were porosities which were caused by manufacturing process not by operation service.

OPR-1000형 증기발생기 ECT 노이즈 측정 시범 적용

천근영(Keun-Young Cheon),문균영(Gyoon-Young Moon) 한국비파괴검사학회 2023 한국비파괴검사학회 춘계학술대회 초록집 Vol.2023 No.5

중수로 칼란드리아 내장품 원격 육안검사 기술 개발

이상훈,진석홍,문균영,Lee, Sang-Hoon,Jin, Seuk-Hong,Moon, Gyoon-Young 한국압력기기공학회 2010 한국압력기기공학회 논문집 Vol.6 No.1

During the period of reinforcement work for the licensing renewal of CANDU NPP, the fuel channels, Calandria tubes and feeders of CANDU Reactor are replaced. The remote visual inspection of Calandria internal is also performed during the period of reinforcement work. This period is a unique opportunity to inspect the inside of the Calandria. The visual inspection for the Calandria vessel and its internals of Wolsong NPP Unit 1 was performed by Nuclear Engineering & Technology Institute(NETEC) of KHNP. To perform this inspection, NETEC developed equipment applied new technology such as the synchronization of 3D CAD, automatic alignment and control system. The inspection confirmed that the Calandria integrity of Wolsong NPP Unit 1 is perfect.

원전 증기발생기 와전류검사 장치의 전기적 특성 측정

이희종,조찬희,유현주,문균영,이태훈,Lee, Hee-Jong,Cho, Chan-Hee,Yoo, Hyun-Joo,Moon, Gyoon-Young,Lee, Tae-Hun 한국비파괴검사학회 2013 한국비파괴검사학회지 Vol.30 No.3

원전 증기발생기는 원자로 냉각재 계통에서 발생한 열에너지를 터빈 계통의 주급수에 전달하여 터빈을 회전시키기 위한 증기를 생산하는 일종의 열교환기이다. 증기발생기 전열관의 손상은 증기발생기의 구조적 및 누설 건전성 유지 능력을 저해시키기 때문에 주기적으로 와전류검사를 수행하여 전열관의 건전성을 평가한다. 증기발생기 전열관의 건전성 평가는 보통 원자로 연료 재장전 기간 중에 수행된다. 현재 국내 증기발생기 전열관에 적용되는 와전류검사는 KEPIC 및 ASME 코드 요건에 따라 수행되며, 와전류검사 수행에 필요한 검사 시스템은 와전류검사 장치와 수집된 신호를 평가하기 위한 평가 프로그램으로 구성된다. 검사에 적용되는 와전류검사 시스템을 구성하는 핵심기기인 와전류검사 장치는 ASME 및 KEPIC 코드에서 총 고조파 왜곡율, 입출력 임피던스, 증폭기 직선성 및 안정성, 위상 직선성, 대역폭 및 복조필터 응답, 디지털 변환, 채널 간섭 등과 같은 전기적 특성을 측정하도록 규정하고 있다. 이에 따라 본 논문에서는 국내 최초로 개발한 원전 증기발생기 와전류검사 장치의 전기적 특성 측정을 위한 ASME 및 KEPIC 코드 요건을 설명하고, 이 요건에 따른 증기발생기 와전류검사 장치의 전기적 특성의 측정 결과를 제시하였다. A steam generator in nuclear power plant is a heatexchager which is used to convert water into steam from heat produced in a nuclear reactor core, and the steam produced in steam generator is delivered to the turbine to generate electricity. Because of damage to steam generator tubing may impair its ability to adequately perform required safety functions in terms of both structural integrity and leakage integrity, eddy current testing is periodically performed to evaluate the integrity of tubes in steam generator. This assessment is normally performed during a reactor refueling outage. Currently, the eddy current testing for steam generator of nuclear power plant in Korea is performed in accordance with KEPIC & ASME Code requirements, the eddy current testing system is consists of remote data acquisition unit and data analysis program to evaluate the acquired data. The KEPIC & ASME Code require that the electrical properties of remote data acquisition unit, such as total harmonic distortion, input & output impedance, amplifier linearity & stability, phase linearity, bandwidth & demodulation filter response, analog-to-digital conversion, and channel crosstalk shall be measured in accordance with the KEPIC & ASME Code requirements. In this paper, the measurement requirements of electrical properties for eddy current testing instrument described in KEPIC & ASME Code are presented, and the measurement results of newly developed eddy current testing instrument by KHNP(Korea Hydro & Nuclear Power Co., LTD) are presented.

와전류검사 기술을 적용한 가압중수로 원전 압력관 비파괴검사

이희종,최성남,조찬희,유현주,문균영,Lee, Hee-Jong,Choi, Sung-Nam,Cho, Chan-Hee,Yoo, Hyun-Joo,Moon, Gyoon-Young 한국비파괴검사학회 2014 한국비파괴검사학회지 Vol.27 No.4

중수로 원자로는 한 개의 원자로용기로 구성된 경수로와는 달리 약 380여개의 연료채널(fuel channel)로 구성되어 있다. 연료채널을 구성하는 압력유지 기기인 압력관(pressure tube)은 지르코니움 합금(Zr-2.5wt% Nb) 재질로서 치수는 내경이 103.4 mm, 두께가 약 4.19 mm, 길이가 6.36 m인 튜브 형태의 관이다. 압력관은 내부에 핵연료 다발과 냉각재가 내장되며 압력관의 기능은 연료를 지지하고 열수송 유체인 중수($D_2O$)를 이송한다. 압력관의 단순한 기하학적인 형상으로 인하여 자동화 비파괴검사가 가능하고 접근성이 우수하다. 연료채널은 경수로형 원전과 동일하게 설치전과 운전중에 원자력안전위원회 법령 요건에 따라 주기적으로 엄격한 비파괴검사를 수행하여 건전성을 확인한다. 연료채널의 주기적 비파괴검사에는 초음파탐상 및 와전류탐상검사 기법을 적용한 체적 비파괴검사 기술이 적용된다. 이중에서 와전류탐상검사 기법은 초음파탐상검사에서 검출된 결함의 확인을 위한 보충검사기술로 적용되고 있지만 표면결함에 대한 검출능이 초음파탐상검사 기법보다 우수한 장점을 가지고 있다. 본 논문에서는 압력관 내부 표면 비파괴검사에 적용되고 있는 와전류탐상검사 기술의 압력관 내면에 발생할 수 있는 결함의 검출 및 깊이 측정 특성에 대한 연구결과를 기술하였다. 즉, 와전류검사 기술은 압력관 내면에 발생할 수 있는 아주 미세한 결함을 매우 우수한 분해능으로 검출할 수 있으므로 초음파탐상검사 결과 확인을 위한 보충기술로서 매우 유용하지만, 결함의 깊이 측정은 오차가 매우 크게 발생하므로 결함 깊이 측정에는 적합하지 않고 오직 표면결함 검출에만 적용하는 것이 바람직하다. A pressurized heavy water reactor (PHWR) core has 380 fuel channels contained and supported by a horizontal cylindrical vessel known as the calandria, whereas a pressurized water reactor (PWR) has only a single reactor vessel. The pressure tube, which is a pressure-retaining component, has a 103.4 mm inside diameter ${\times}$ 4.19 mm wall thickness, and is 6.36 m long, made of a zirconium alloy (Zr-2.5 wt% Nb). This provides support for the fuel while transporting the $D_2O$ heat-transfer fluid. The simple tubular geometry invites highly automated inspection, and good approach for all inspection. Similar to all nuclear heat-transfer pressure boundaries, the PHWR pressure tube requires a rigorous, periodic inspection to assess the reactor integrity in accordance with the Korea Nuclear Safety Committee law. Volumetric-based nondestructive evaluation (NDE) techniques utilizing ultrasonic and eddy current testing have been adopted for use in the periodic inspection of the fuel channel. The eddy current testing, as a supplemental NDE method to ultrasonic testing, is used to confirm the flaws primarily detected through ultrasonic testing, however, eddy current testing offers a significant advantage in that its ability to detect surface flaws is superior to that of ultrasonic testing. In this paper, effectiveness of flaw detection and the depth sizing capability by eddy current testing for the inside surface of a pressure tube, will be introduced. As a result of this examination, the ET technique is found to be useful only as a detection technique for defects because it can detect fine defects on the surface with high resolution. However, the ET technique is not recommended for use as a depth sizing method because it has a large degree of error for depth sizing.

국내 원전 원자로용기 내부 가동중검사 고찰

김진회(Jin Hoi Kim),강준승(Jun Seung Kang),문균영(Gyoon Young Moon) 한국에너지학회 2023 한국에너지공학회 학술발표회 Vol.2023 No.4