http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
( Alireza Ashtiani Araghi ),( Chun Gu Lee ),( Seong In Cho ),( Joong Yong Rhee ) 한국농업기계학회 2015 바이오시스템공학 Vol.40 No.1
Purpose: To present a flexible and accurate autonomous solution for creating any desired row spacing value between the hydroponic gullies in multilayer growing units, and evaluate the capabilities and performance of the relevant automated system through the use of virtual prototyping technique. Methods: To build the virtual prototype of the system, CAD models of its different parts, including an autonomous vehicle and the mechanical mechanisms embedded in the multilayer growing unit, were developed and imported into the Recur Dyn simulation software. In order to implement the automated row spacing operation, three spacing modes with different loading cycles and working steps were defined, and the operation of the system was simulated to obtain the target row spacing values specified for each of these modes. Results: Motion profiles related to the horizontal displacement of: 1) the lower and upper sliding bars installed in the cultivation layers, and 2) the hydroponic gullies, during the simulation of the system operation, were generated and analyzed. No deviation from the specified target spacing values was observed at the end of simulations for all spacing modes. Conclusions: The results of the motion analysis obtained by simulating the system operation confirm the effectiveness of the control scheme proposed for automated row spacing of gullies. It was also found that proper sequencing of the loading cycles and the precision of the working strokes of the upper bars are the critical factors for establishing a certain row spacing value. Based on the simulation results, precise control of the back and forth motions of the upper bars is highly necessary for sound operation of the real system.
Ashtiani-Araghi, Alireza,Lee, Chungu,Cho, Seong-In,Rhee, Joong-Yong Korean Society for Agricultural Machinery 2015 바이오시스템공학 Vol.40 No.1
Purpose: To present a flexible and accurate autonomous solution for creating any desired row spacing value between the hydroponic gullies in multilayer growing units, and evaluate the capabilities and performance of the relevant automated system through the use of virtual prototyping technique. Methods: To build the virtual prototype of the system, CAD models of its different parts, including an autonomous vehicle and the mechanical mechanisms embedded in the multilayer growing unit, were developed and imported into the RecurDyn simulation software. In order to implement the automated row spacing operation, three spacing modes with different loading cycles and working steps were defined, and the operation of the system was simulated to obtain the target row spacing values specified for each of these modes. Results: Motion profiles related to the horizontal displacement of: 1) the lower and upper sliding bars installed in the cultivation layers, and 2) the hydroponic gullies, during the simulation of the system operation, were generated and analyzed. No deviation from the specified target spacing values was observed at the end of simulations for all spacing modes. Conclusions: The results of the motion analysis obtained by simulating the system operation confirm the effectiveness of the control scheme proposed for automated row spacing of gullies. It was also found that proper sequencing of the loading cycles and the precision of the working strokes of the upper bars are the critical factors for establishing a certain row spacing value. Based on the simulation results, precise control of the back and forth motions of the upper bars is highly necessary for sound operation of the real system.
Evaluation of a Crank-type Walking Cultivator for Upland Farming
Kwon, Tae Hyeong,Ashtiani-Araghi, Alireza,Lee, Chungu,Kang, Tae Gyoung,Lee, Byeong-Mo,Rhee, Joong-Yong Korean Society for Agricultural Machinery 2014 바이오시스템공학 Vol.39 No.1
Purpose: This research was conducted to evaluate feasibility of a crank-type walking cultivators for weeding in furrowed upland. Methods: A walking cultivator developed by RDA was selected and evaluated with its working speed (S), cultivation depth (CD) and weeding performance (WP). The evaluation was performed in upland field on July and August, 2012. Also kinematic analysis of the machine was performed to draw out design improvements. Results: S in flat, uphill and downhill were about 0.11 m $s^{-1}$, 0.11 m $s^{-1}$, and 0.13 m $s^{-1}$ respectively. It was found that S had a low relevance with user conditions. The CD was 35 ~ 40 mm which was satisfied with the RDA guide for weeding machine. A wide variation was observed in values of WP depending on the growth stages of weeds and field conditions. The cultivator showed low performance in eliminating the well-grown weeds. Kinematic simulation revealed that high forward speed caused a high ratio of un-weeded area. Conclusions: The weeding performance of the cultivator was satisfactory for weeds in early growth stage but it showed difficulties in handling on up-slope and in entering up-land. Specifically, the weight of the cultivator was judged as overweight for female workers. The crank-hoe type cultivator was judged as unsuitable for small walking type machine due to weight of the four-bar linkage system. Kinematic analysis revealed that the ratio of crank speed to the ground speed must be 850 rpm s $m^{-1}$ (255 rpm based on 0.3 m $s^{-1}$) or greater to avoid uncultivated area. Selection of forward speed is a decisive factor in designing the weeding cultivator.
( Tae Hyeong Kwon ),( Alireza Ashtiani Araghi ),( Chun Gu Lee ),( Tae Gyoung Kang ),( Byeong Mo Lee ),( Jong Yong Rhee ) 한국농업기계학회 2014 바이오시스템공학 Vol.39 No.1
Purpose : This research was conducted to evaluate feasibility of a crank-type walking cultivators for weeding in furrowed upland. Methods: A walking cultivator developed by RDA was selected and evaluated with its working speed (S), cultivation depth (CD) and weeding performance (WP). The evaluation was performed in upland field on July and August, 2012. Also kinematic analysis of the machine was performed to draw out design improvements. Results: S in flat, uphill and downhill were about 0.11 m s-1, 0.11 m s-1, and 0.13 m s-1 respectively. It was found that S had a low relevance with user conditions. The CD was 35 ~ 40 mm which was satisfied with the RDA guide for weeding machine. A wide variation was observed in values of WP depending on the growth stages of weeds and field conditions. The cultivator showed low performance in eliminating the well-grown weeds. Kinematic simulation revealed that high forward speed caused a high ratio of un-weeded area. Conclusions: The weeding performance of the cultivator was satisfactory for weeds in early growth stage but it showed difficulties in handling on up-slope and in entering up-land. Specifically, the weight of the cultivator was judged as overweight for female workers. The crank-hoe type cultivator was judged as unsuitable for small walking type machine due to weight of the four-bar linkage system. Kinematic analysis revealed that the ratio of crank speed to the ground speed must be 850 rpm s m-1 (255 rpm based on 0.3 m s-1) or greater to avoid uncultivated area. Selection of forward speed is a decisive factor in designing the weeding cultivator.
Kwon, TaeHyeong,Kim, JoonYong,Lee, Chungu,Park, Gun-Hwan,Ashtiani-Araghi, Alireza,Baek, Seung Hwan,Rhee, Joong-Yong Korean Society for Agricultural Machinery 2014 바이오시스템공학 Vol.39 No.1
Purpose: The modern IT can give enormous impacts on the agricultural production and consumption. However, farmer's ability to use IT devices has been known as one of the critical factors on success of IT in agriculture. This survey study was performed to evaluate the informatization status of farmers and to draw a strategy to develop and distribute a ubiquitous agricultural information system. Methods: A survey questionnaire with 19 questions on the degree of IT devices such as computers and smartphones and their utilization were developed. The survey was questioned 3 groups of farmers in Gyounggi Province and analyzed statistically by the ${\chi}^2$ test. Results: The order of IT devices distribution were computers, smartphones, smart TVs and tablet PCs in all groups. The ratios of ownerships of the devices are 97.7, 78.6%, 31.4%, 17.8% respectively. The active farmers in this survey showed higher informatization level than that of native and the general farmers. Conclusions: The ubiquitous agricultural information system was judged to be developed for the computer because spread and use of it exceeds the other devices. Also, the information system based on the smartphone could be a complementary way if the rapid of the smartphones continues and proper education on use of the phone is provided.
( Seung Hwan Yang ),( Chun Gu Lee ),( Won Kyu Lee ),( Alireza Araghi Ashtiani ),( Joon Yong Kim ),( Sang Deok Lee ),( Joong Yong Rhee ) 한국농업기계학회 2012 바이오시스템공학 Vol.37 No.1
Purpose: Utilizing air thermal energy during over-heated time in the greenhouse is a necessary component to save greenhouse heating costs for nighttime. However, there is no practical way to implement the related principles. Methods: In this study, a heating and cooling system which utilizes the surplus air thermal energy in a greenhouse was developed. Available air thermal energy and heating load for this experimental glasshouse were estimated based on temperature conditions of the plant growth and weather data. Results: Estimated values were 400 MJ/day for maximum surplus air thermal energy and 340 MJ/day for maximum heating energy which were target values of the design as well. The system consists of a heat pump, fan-coil units and heat storage tanks which are divided into low and high temperature tanks. Moreover, a new control logic was developed for surplus air thermal energy utilization. Conclusions: This paper explains the details of conceptual design process of the system. Results of test operations showed that the developed system performed the recovery and supply of the thermal energy according to design purposes.
Yang, Seung-Hwan,Lee, Chun-Gu,Lee, Won-Kyu,Ashtiani, Alireza Araghi,Kim, Joon-Yong,Lee, Sang-Deok,Rhee, Joong-Yong Korean Society for Agricultural Machinery 2012 바이오시스템공학 Vol.37 No.1
Purpose: Utilizing air thermal energy during over-heated time in the greenhouse is a necessary component to save greenhouse heating costs for nighttime. However, there is no practical way to implement the related principles. Methods: In this study, a heating and cooling system which utilizes the surplus air thermal energy in a greenhouse was developed. Available air thermal energy and heating load for this experimental glasshouse were estimated based on temperature conditions of the plant growth and weather data. Results: Estimated values were 400 MJ/day for maximum surplus air thermal energy and 340 MJ/day for maximum heating energy which were target values of the design as well. The system consists of a heat pump, fan-coil units and heat storage tanks which are divided into low and high temperature tanks. Moreover, a new control logic was developed for surplus air thermal energy utilization. Conclusions: This paper explains the details of conceptual design process of the system. Results of test operations showed that the developed system performed the recovery and supply of the thermal energy according to design purposes.