http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
건설업 사고 발생원인 파악을 위한 사고 분석 모델 개발
임원준 ( Won Jun Lim ),기정훈 ( Jung Hun Kee ),성주현 ( Joo Hyun Seong ),박종일 ( Jong Yil Park ) 한국안전학회(구 한국산업안전학회) 2019 한국안전학회지 Vol.34 No.1
Accident analysis models were developed to improve the construction site safety and case studies was conducted. In 2016, 86% of fatality accidents occurred due to simple unsafe acts. Structure related accidents are less frequent than the non structure related causes, but the number of casualties per accident is two times higher than non structure one. In the view of risk perception, efforts should be given to reduce accidents caused by low frequency - high consequence structure related causes. In case of structure related accident, structural safety inspection and management (including quality), ground condition management / inspection technology, and provision of risk information delivery system in case of non structure related accident were proposed as a solution. In analysis of relationship between safety related stakeholder, the main problem were the lack of knowledge of controller and player, loss of control due to duplicated controls, lack of communication system of risk information, and relative position error of controller and player.
가역성이 우수한 도자기 복원용 Urethane resin의 개발 및 물성에 대한 연구
오승준,박기정,위광철,Oh, Seung Jun,Park, Gi Jung,Wi, Koang Chul 한국문화재보존과학회 2015 보존과학회지 Vol.31 No.1
현재 토기 및 도자기를 보존처리 할 때 사용되고 있는 접착 복원제의 경우 크게 Epoxy계, Cellulose계, Cyanoacrylate계 등이 사용되고 있으나 재료에 따라 심한 수축으로 인한 재탈락, 황변 현상으로 인한 색상 변화, 사용시 도구와 손에 묻어나오는 불편한 작업성, 비가역성 등 다양한 문제점을 나타내고 있다. 본 연구에서는 도자기 복원용으로 사용되고 있는 Epoxy resin의 황변 현상과 비가역성의 문제점 해결을 목적으로 저황변, 가역성이 우수한 Urethane계 합성수지를 개발하였다. 개발된 Urethane resin의 접착력은 원액 2.07MPa로 기존 재료인 $EPO-TEK301^{(R)}$ 1.21MPa로 1.5배 이상의 우수한 물성을 지니고 있다. 가공성 측정 결과 Urethane resin(in Talc 50wt%)의 마모율이 1.09%로 기존 재료인 Quick $Wood^{(R)}$(1.02%)의 마모율 보다는 다소 높게 측정되었으며, EPO-$TEK301^{(R)}$(0.41%)와 $L30^{(R)}$ (0.39%)보다 는 2배 이상의 마모율을 보이고 있어 기존의 재료보다 쉽게 성형 과정이 이루어질 수 있는 장점을 지니고 있다. Urethane resin의 장점인 가역성 실험은 Acetone, Ethyl Alcohol 침적 후 12시간 경과 후 Urethane resin과 충전제인 Talc가 분말화 현상을 나타내며 100% 용해되었으며, 기존 Epoxy resin의 가역성이 0%인 것에 비해 매우 우수한 가역성을 지니고 있다. 내구성 평가를 위한 자외선 실험 결과 Urethane resin의 원액 기준 ${\Delta}E^*ab$ 색상 변화 값이 자외선 노출 전 후 2.76로 기존의 Epoxy resin보다 약 7~20배 정도 줄어 황변 현상으로 인한 이질감의 문제점을 최소화하였다. In the case of adhesives & restoration agents currently being used for the preservation treatment of ceramics and earthenware, epoxy type, cellulose type and cellulose type are mainly being used. However, they are showing various problems such as re-detachment from severe contraction, color change from yellowing, work inconvenience of staining on tools and hand during usage and irreversibility. For the purpose of solving the issues of yellowing and irreversibility of epoxy resin being used to restore ceramics, urethane synthetic resin with low yellowing excellent reversibility has been developed in this study. The adhesive strength of urethane resin that has been developed has excellent properties with 2.07MPa for undiluted solution, which is 1.5 times higher than that of existing material EPO-$TEK301^{(R)}$ 1.21MPa. The result of workability measurement showed that the wear rate of urethane resin (in Talc 50wt%) was 1.09%, which was somewhat higher than that of existing material Quick $Wood^{(R)}$ (1.02%). In addition, its wear rate is two times higher than that of $EPO-TEK301^{(R)}$ (0.41%) and $L30^{(R)}$ (0.39%), thereby showing an advantage in its forming process compared to existing materials. As for the advantage of urethane resin of reversibility experiment, 12 hours after acetone, ethyl alcohol deposition, urethane resin and filler talc were dissolved 100% while showing powdering phenomenon. Compared to 0% reversibility of existing epoxy resin, it has much superior reversibility. The result of UV rays experiment to evaluate its durability showed that ${\Delta}E^*ab$ color change value based on undiluted solution of urethane resin was 2.76 before & after UV rays exposure, which was a decrease by about 7-20 times compared to that of existing resin, thereby minimizing the issue of heterogeneity.
시뮬레이션 훈련이 뇌졸중 환자의 균형 능력에 미치는 영향
오승준,안명환,Oh, Seung Jun,Ahn, Myung Hwan 대한물리치료과학회 2013 대한물리치료과학회지 Vol.20 No.1
Purpose : Investigate the effects of Horse-back riding Simulation Machine training on the Balance ability in Patients with Stroke. Method : The patients were divided to control group(n=18) with conventional rehabilitation conventional rehabilitation 60min/day and experimental group(n=17) with hippotherapy simulator 15 min/day after conventional rehabilitation 45min/day, 5 time/week for 4 weeks. Balance ability of both groups was assessed using Timed Up and Go(TUG), Berg balabce scale(BBS) and Center of pressure area(COPA). In the present result, there was a no significant(P>0.05) Results : The results of this study showed that Horse-back riding Simulation Machine training, after training, had meaningful difference of TUG, BBS and COPA. Conclusion : This study showed that Horse-back riding Simulation Machine training increased balance ability that resulted in enhancement of motor performance.
카라기난 기반 액상형 바이오 종이 접착제의 제조 및 물성에 관한 연구
오승준,한원식,위광철,Oh, Seung-Jun,Han, Won-Sik,Wi, Koang-Chul 한국문화재보존과학회 2020 보존과학회지 Vol.36 No.6
휘발성 유기 화합물 기반의 접착제를 대체하고자 천연 재료에 대한 수요가 늘고 있지만, 제조 및 생산의 전 과정에서 휘발성 유기화합물 사용을 일절 배제할 경우, 제조의 곤란, 생산성 및 보존성의 저하 등의 단점이 나타났다. 본 연구에서는 해조류의 카라기난 성분을 이용해 천연바이오 접착제를 제조하고 종이 접착제로서의 가능성을 확인해보고자 하였다. 카라기난을 이용한 액상형 바이오 종이 접착제의 제조에서 carrageenan의 겔화는 접착제의 제조과정, 발림성, 균일성, 접착 강도의 문제를 나타내게 된다. 이를 위하여 추출된 전체 carrageenan 중에서 λ-carrageenan만을 분리하여 사용하였으며 이로 인하여 매우 안정된 종이 접착제의 제조가 가능하였다. 최종 조성은 λ-carrageenan 52.0 ± 1.0%, polyvinylpyrrolidone 30.5 ± 0.5%, ethylhexylglycerin 1.0 ± 0.05%, glycerin 1.5 ± 0.05%, dextrine 13.5 ± 0.5%, 식품용 소포제 FD330A 0.6 ± 0.05%의 조성이었다. 이들이 나타내는 점도는 1.13 ± 0.07 × 10<sup>5</sup> cPs (25℃), pH 6.22, 건조속도 15 min, △b<sup>*</sup> -10.79, △E<sup>*</sup>ab 8.18의 자외선 열화 결과를 나타내고 있었으며 44.63 kgf/cm<sup>2</sup>의 매우 우수한 접착 강도를 나타내고 있었다. 이 접착제는 TVOC, HCHO 및 중금속 모두에서 불검출 결과를 나타내었으며 총호기성생균수 측정과 ASTM G 21-15 시험법에 의하여 곰팡이 challenge test에서도 곰팡이에 대한 우수한 저항성 결과를 나타내고 있어서 접착제의 항속성에서도 우수한 결과를 나타내고 있는 것으로 보인다. There is a growing demand for natural materials to replace adhesives based on volatile organic compounds (VOCs). However, the exclusion of VOCs from the manufacturing process leads to difficulties in manufacturing, and reduction in productivity and preservability. In this paper, we report the manufacture of natural bioadhesives using the carrageenan component of seaweed. λ-carrageenan, isolated from the extracted total carrageenan, was used to prepare a highly stable adhesive for paper. The resulting composition was 52.0 ± 1.0% λ-carrageenan, 30.5 ± 0.5% Polyvinylpyrrolidone, 1.0 ± 0.05% ethylhexylglycerin, 1.5 ± 0.05% glycerin, 13.5 ± 0.5% dextrine, and 0.6 ± 0.05% food-grade antifoam emulsion. The viscosity was found to be 1.13 ± 0.07 × 105 cP (25℃), UV degradation occurred at pH6.22, drying rate was 15min, △b<sup>*</sup> was -10.79, and △E<sup>*</sup> ab was 8.18. The bioadhesive showed an excellent adhesion strength of 44.63 kgf/cm<sup>2</sup>. Thus this adhesive showed excellent fungal resistance and good adhesive persistence, without the presence of total volatile organic compounds (TVOC), formaldehyde (HCHO), and heavy metals.
오승준(Oh Seung-Jun),전재열(Chun Jae-Youl) 대한건축학회 2004 大韓建築學會論文集 : 構造系 Vol.20 No.8
The communication among the design participant who architecture, structure, HVAC, electric engineer have not been smooth<br/> in design process of architectural project in Korea.<br/> Therefore designs have not been suitable for performance requirement, cost and constructability. The reason why these<br/> problems happened that the result of design is not corresponding to design change is caused by variable factor from design till<br/> construction phase; therefore the problem (low quality etc.) has been happened because of disagreement between<br/> Multi-disciplinary drawings.<br/> For the purpose of this research, is to propose the establishment method of decision support model for the cooperative design<br/> in order to provides improved design coordination and optimize the building system. and vivificated the applicability of<br/> proposed decision support model through case study.
바람직한 청소년교육과 스포츠 강사 지도 유형에 관한 연구
오승준(Seung-Jun Oh),최현욱(Hyun-Wook Choi) 한국엔터테인먼트산업학회 2017 한국엔터테인먼트산업학회논문지 Vol.11 No.3
본 연구는 스포츠강사의 지도유형과 청소년의 교육적 관계를 밝히는 데 그 목적이 있다. 이를 위해 최근 학계에서 많이 이용되는 요인들을 이용하여 스포츠강사의 지도유형이 수업몰입 및 수업만족도에 미치는 영향을 규명하고자 한다. 연구목적에 따라 서울지역에 있는 중학생 475명의 자료를 분석하여 다음과 같은 결론을 얻었다. 첫째, 스포츠강사의 지도유형은 수업몰입에 영향을 미친다. 둘째, 스포츠강사의 지도유형과 수업몰입은 수업만족도에 영향을 미친다. 셋째, 스포츠강사의 지도유형과 수업만족도 간의 관계에서 수업몰입은 매개효과가 있다. 마지막으로 수업 행동과 의식의 일치는 사회적지지 행동형과 교수 · 지시형이 매개효과를 지니고 있었다. The Purpose of this study is to identify relationship between the types of sport instructor and adolescent education. We utilized the most often used factors, in order to identify that the types of sport instructor effect in class Commitment and the degree of satisfaction with class. To achieve the goal of this study, a total of 475 surveys collected and required the conclusion below. First, the types of sport instructor have an effect on class Commitment. Second, the types of sport instructor and class Commitment have an effect on the degree of satisfaction with class. Third, on the relationship between the types of sport instructor and the degree of satisfaction with class, class Commitment have a mediate effect. Lastly, social support behavior and direction type have a mediate effect on the class behavior and harmonize of consciousness.
야외 금속 조각 작품 표면 보존용 액상형 wax의 제조 및 적용성 연구
오승준 ( Oh Seung Jun ),위광철 ( Wi Koang Chul ) 한국기초조형학회 2020 기초조형학연구 Vol.21 No.6
야외 조각 공원 설치 작품 및 환경 조형물은 대기환경오염물과 자외선, 생물학적 피해 등으로 인해 손상되고 작품 본래의 형상이 변형되어 작가의 의도와 다른 전달력과 왜곡된 미적 정보를 전달하고 있다. 이를 방지하기 위해 미술사적 과학적 보존처리가 이루어지고 있으며, 이중 금속 재질의 야외 조각 작품 보존 시 작품의 표면 보존을 위해 wax 코팅이 이루어지고 있다. wax는 코팅 후 작품이 왜곡되어 보이지 않으며 가역성이 있어 보존 재료로서 사용되어지고 있는 반면에 대기오염물질과 산성비, 염수, 먼지 등에 의해 노화가 진행되고 이는 코팅력, 내구성, 내열성, 차단성, 황변성 등이 저하되는 현상과 이로 인해 처리 후 지속적인 관리와 주기적인 재처리가 필요하다. 이에 본 연구에서는 현재 야외 금속조각 작품 표면 보존용 재료인 3종의 wax보다 성능이 개선된 wax를 제조하여 염수분무, 자외선 열화, 접촉각 등의 물성 실험으로 적용 가능성에 대해 판단해보고자 하였다. 연구결과 기존에 사용되어 온 3종의 wax(C, O, Q-wax) 보다 수분 및 습기에 대한 차단성과 지속성, 자외선으로부터의 내구성이 증진된 wax를 제조하였으며, 제조된 L-wax는 대기오염물질 등으로부터 2배 이상의 차단성과 코팅 지속력을 나타내었으며, 자외선 차단 효과는 약 6~30배 이상 증진되어 wax의 노화 방지에 우수한 효과가 있다고 판단된다. 또한 기존 wax의 코팅방법인 Deep 코팅 방법이 아닌 분무법으로 사용이 가능하도록 제조하여 작업의 편리성을 확보하고, 분사를 통한 세밀한 부분까지의 코팅이 보다 수월하게 이루어져 작업성이 개선될 수 있다고 판단되며, 코팅 시 열을 가하지 않고 저독성 용제를 사용한 재료로서 인체의 안전성, 화재로부터의 안정성을 확보할 수 있을 것으로 사료된다. 이러한 결론을 기반으로 추가적인 연구가 이루어진다면 작품 본래의 형태, 재질, 정보력, 전달력, 전시효과, 재처리로 인한 작품의 피로도 증가 등을 예방할 수 있을 것으로 판단된다. Outdoor sculpture park installation works and environmental sculptures are damaged by air pollutants, ultraviolet rays, biological damage, etc., and the original shape of the work is transformed, conveying a different transmission power and distorted aesthetic information from the artist's intention. In order to prevent this, art history and scientific preservation treatment is performed, and wax coating is applied to the outdoor sculptures made of double metal to preserve the surface of the work. Wax is used as a preservation material as it does not distort the work after coating and has reversibility, whereas aging progresses by air pollutants, acid rain, salt water and dust, causing deterioration of coating power, durability, thermostability, interrupting performance, so continuous management and periodic reprocessing are required. Thus, this study tried to determine the applicability of waxes with improved performance than three types of waxes used for preserving the surface of outdoor metal sculptures, by experimenting with properties such as salt spray, UV degradation, and contact angle. Results show that a wax with improved barrier properties against water and moisture, and durability against UV rays than previous ones (C, O, Q-wax) was manufactured, and L-wax showed more than twice the barrier properties and coating power, and UV blocking effect was improved by about 6-30 times with excellent effect in preventing aging of wax. Workability can also be improved by making it possible to use the spray method instead of the existing deep coating method, securing convenience of work with easier coating to the detailed parts through spraying. As a material using a low-toxic solvent without applying heat during coating, it can secure human safety from fire. If additional research is conducted based on this conclusion, the original form, material, information power, transmission power, exhibition effect, and increased fatigue of the work due to reprocessing can be prevented.
스마트폰 어플리케이션을 이용한 뇌졸중 환자의 등뼈 만곡, 골반기울기 측정에 대한 타당도 연구
오승준 ( Seung-jun Oh ),김도현 ( Do-hyun Kim ) 대한신경치료학회 2020 신경치료 Vol.24 No.3
Purpose The aim of this study was to determine of validity of thoracic kyphosis and pelvic tilt using smartphone application in chronic stroke patients. Methods Subjects were stroke patients (n=15) and healthy controls (n=15). The minimal detectable change (MDC) and standard error of measurement (SEM) were estimated to determine a real change for thoracic kyphosis and pelvic tilt angle. Correlation was analyzed to explore the relationships between smartphone application and inclinometer. Results The thoracic kyphosis and pelvic tilt angle had an SEM of 1.88, 1.10, MDC of 3.68, 2.17. The high correlation was observed between the measured with the inclinometer data and the measured by the smartphone application data (thoracic kyphosis, r=0.93, p<0.001; pelvic tilt r=0.93, p<0.001). Conclusion Our experimental results indicate that smartphone application was appropriate to measure thoracic kyphosis and pelvic tilt angle in stroke patients.