http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
착저형 수중장비를 이용한 수중작업 시 작업경계면 인식을 위한 소나시스템 활용법
신창주(Changjoo Shin),장인성(In-Sung Jang),원덕희(Deokhee Won),서정민(Seo Jung-min),백원대(Won-Dae Baek),김기훈(Kihun Kim),김종훈(KIM JONG HOON) 한국산학기술학회 2016 한국산학기술학회논문지 Vol.17 No.10
수중사석고르기 장비와 같은 착저형 수중장비를 활용하여 해저면에서 수중 작업을 수행할 경우 해당 장비는 작업경계면을 정확히 인식하고 작업장 내에 자리잡고 있는 것이 중요하다. 이는 장비 전복과 같이 장비 안전사고와 직결될 수 있기 때문이다. 이 때 작업경계면 표식을 위해서는 잠수부의 도움이 필수적인데, 이를 위하여 잠수부가 수중작업을 수행할 때 작업이 용이하면서도 시중에서 쉽게 구할 수 있으며 재료를 선정하는 것이 중요한데 나일론줄을 해저면에 설치하여 작업경계를 표시하도록 하였다. 수중에서 주변 환경을 관찰하기 위하여 소나와 팬틸트를 이용하여 소나시스템을 구성하였으며 이를 이용하여 거리변화에 따른 수중 작업경계면 탐지 여부를 확인하였다. 또한 수중사석고르기 장비에 최종적으로 소나시스템을 설치하고 나일론줄로 표시된 작업경계면에 대한 탐지여부를 검증하였다. 본 연구결과를 활용하여 착저형 수중장비를 이용한 수중작업 시 작업경계면 인식을 수행할 수 있는 방안을 확보하였다. 작업경계면 인식 방안을 활용할 경우 추후에 개발될 수 있는 다양한 종류의 착저형 수중작업 장비의 작업절차에 광범위하게 적용할 수 있을 것으로 판단된다. The detection of an underwater work space boundary is very important when an underwater construction is carried out using seabed type underwater equipment, such as underwater machines for rubble mound leveling, because it can induce industrial disasters. Therefore, divers are needed to mark the underwater work space boundary. A nylon rope is used to improve the convenience during an underwater diver"s work. The results showed that the work space boundary can be detected using a sonar system. Using these results, an efficient method to detect the underwater work space boundary can be obtained when an underwater construction is carried out using seabed type underwater equipment.
신창주(Changjoo Shin),홍진숙(Chinsuk Hong),정의봉(Weuibong Jeong),정상우(Sangwoo Jeong) 한국소음진동공학회 2010 한국소음진동공학회 학술대회논문집 Vol.2010 No.10
This paper reports active control of clamped beams using acceleration feedback controllers (AF). The equations of motion of clamped beam under force and moment pairs were derived and the equations of AF controllers were formulated. The effect of the parameters - gain and damping ratio - of the AF controllers on the open loop transfer function was investigated mainly in terms of the system stability. Increasing the gain of the AF controller tuned at a mode, the magnitude of the open loop transfer function is increased at all frequencies. The increase of the damping ratio of the AF controller leads to decrease the magnitude of the open loop transfer function and modifies its phase characteristics to be more stable. Three AF controllers connected in parallel were then proposed. Each AF controller is tuned at the 2nd, 3rd and 4th modes, respectively. Their parameters were determined to remain the system to be stable based on the results of the parametric study. A significant reduction in vibration at the 3 modes can be obtained.
Filtered Velocity Feedback 제어기를 이용한 양단지지보의 능동진동제어
신창주(Changjoo Shin),홍진숙(Chinsuk Hong),정의봉(Weuibong Jeong) 한국소음진동공학회 2011 한국소음진동공학회 학술대회논문집 Vol.2011 No.4
This paper reports a filtered velocity feedback (FVF) controller, which is an alternative to direct velocity feedback (DVFB) controller. The instability problems due to high frequency response under DVFB can be alleviated by the suggested FVF controller. The FVF controller is designed to filter out the unstable high frequency response. The FVF controller and the dynamics of clamped beams under forces and moments are first formulated. The effects of the design parameters (cut-off frequency, gain, and damping ratio) on the stability and the performance are then investigated. The cut-off frequency should be selected not to affect the system stability. The magnitude of the open loop transfer function (OLTF) at the cut-off frequency should be small. As increasing the gain of the FVF controller, the magnitude of the OLTF is increased, so that the closed loop response can be reduced more. The enhancement of the OLTF at the cut-off frequency is reduced but the phase behavior around the cut-off frequency is distorted, as the damping ratio is increased. The control performance is finally estimated for the clamped beam. More than 10dB reductions in velocity response can be achieved at the modal frequencies from the first to eighth modes.
Filtered Velocity Feedback 제어기를 이용한 양단지지보의 음향파워 저감
신창주(Changjoo Shin),홍진숙(Chinsuk Hong),정의봉(Weuibong Jeong) 한국소음진동공학회 2011 한국소음진동공학회 학술대회논문집 Vol.2011 No.10
This paper reports the filtered velocity feedback (FVF) controller to reduce the acoustic power from clamped beams. The instability problem due to the non-collocated sensor/actuator configuration when using PZT actuator should be resolved. The roll-off property of the FVF controller at high frequency helps to alleviate the instability. The dynamics of clamped beams under forces and moments pair and the FVF controller are first formulated. The formulation of the sound radiated power is followed. The open loop transfer function (OLTF) synthesized with 100 modes is used to determine the stability of the control system. The control performance is finally estimated. The levels of the vibration and the sound radiated power are reduced in the wide band below the tuning mode of the FVF controller.
신창주(Changjoo Shin),홍진숙(Chinsuk Hong),정의봉(Weuibong Jeong) 한국소음진동공학회 2012 한국소음진동공학회 학술대회논문집 Vol.2012 No.4
This paper reports the active vibration control of plates using positive position feedback controller (PPF). The equations of motion of the plate under force and moment pairs were derived and the equations of PPF controllers were formulated. The effect of the parameters ? gain and damping ratio ? of the PPF controllers on the open loop transfer function was investigated mainly in terms of the system stability. Increasing the gain of the PPF controller tuned at a mode, the magnitude of the open loop transfer function is increased at all frequencies without changing the phase behavior. The increase of the damping ratio of the PPF controller leads to decrease the magnitude of the open loop transfer function and to modify its phase characteristics to be more stable. Two PPF controllers connected in parallel, Each PPF controller is tuned at the 1st and 2nd modes, respectively. Their parameters were determined to remain the system to be stable based on the results of the parametric study. A significant reduction in vibration at the 2 modes can be obtained.
신창주(Changjoo Shin),권오순(Osoon Kwon),서정민(Seo Jungmin),강현(Hyoun Kang) 한국산학기술학회 2019 한국산학기술학회논문지 Vol.20 No.3
한국해양과학기술원은 해저에서 지면 굴착 작업이 가능한 트랙 형태의 수중건설로봇 (URI-R)을 개발 중에 있다. 개발 로봇은 수중에서 굴착 작업을 수행하는 동안 강한 소음 및 진동 환경에 노출된다. 이로 인하여 음향을 이용하여 수중 위치 신호를 획득하여야 하는 개발 장비는 신호획득이 어려운 상황에 빈번하게 놓일 수 있다. 이를 극복하기 위하여 개발 장비가 수중 위치 신호가 간헐적으로 들어오는 상황 속에 놓여 있어도 연속적으로 자신의 위치를 인식하는 방안을 확보하는 것이 필요하다. 본 논문에서는 비용절감 및 다양한 실험케이스를 확보하기 위하여 수중 작동 특성을 모사할 수 있는 실험을 육상에서 재현하여 실험하였으며 위치 추정을 위하여 관성항법 및 위성항법신호를 사용하였다. 위치 신호획득 주기가 길어짐에 따라 자기 위치 추정에 미치는영향을 실험적으로 고찰하였다. 이를 통하여 URI-R의 연속적인 자기 위치 인식을 수행하기 위한 위치 신호획득의 최대 주기를 확인하고 이를 적용하고자 한다. A track type underwater construction robot(URI-R) which can trench on seabed is being developed by Korea Institute of Ocean Science & Technology. During the underwater trenching work, the robot is exposed high intensive noise and vibration so the underwater localization signal may not be obtained properly by the acoustic tracking system. Therefore it is necessary to research about continuous localization even though the measured position signal comes in intermittently. In this paper, the experiments were carried out on land to simulated the underwater operating environment characteristics. To estimate its position, inertial navigation system and global navigation satellite system are used. The effects of the period variation while localizing is investigated by the experiments, and the application for URI-R is proposed.
탁도가 높은 수중작업현장에 사용 가능한 소나시스템의 성능 분석
신창주(Shin, Changjoo),장인성(Chang, In-Soung),김기훈(Kim, Ki-Hoon),최현택(Choi, Hyun-Tack),이승현(Lee Seung-Hyun) 한국산학기술학회 2013 한국산학기술학회논문지 Vol.14 No.9
수중사석고르기와 같은 수중공사작업을 수행하기 위하여 개발 진행 중인 무인수중장비를 수중공사현장에 투 입할 경우, 작업 시 발행하는 부유물들로 인하여 탁도가 높아진다. 이러한 수중환경에서 광학카메라를 이용할 경우, 수중전방인식이 불가능할 수 있다. 이를 극복하기 위하여 무인수중장비에 소나를 탑재하고자 한다. 소나를 무인수중 장비에 적용하기에 앞서, 본 연구에서는 소나의 분해능, 탁도가 높은 물 속에서 스캐닝한 소나이미지를 확인하여 장 비의 성능을 분석하였다. 그리고 수중공사현장의 경계면을 표시하기 위한 방법을 제안하였다. 이를 통하여 무인수중 장비에 적용하기 위한 소나의 기초 성능을 확인하였다. The developing unmanned underwater equipment can be used for underwater construction site such as underwater leveling works. If a optical camera is applied to the unmanned underwater equipment, recognition in underwater can be gone to low due to high turbidity in working field. To overcome this problem, a sonar will be installed to the unmanned underwater equipment. In this study, the resolution of the sonar and the quality test of the sonar image under high turbidity environment were conducted. And the method to indicate the boundary of the underwater construction site was proposed. By these results, the basic performance of the sonar was evaluated.