http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
Sanchez-Majado S.,Torralba J. M.,Jimenez-Morales A. 한국분말야금학회 2006 한국분말야금학회 학술대회논문집 Vol.2006 No.1
The corrosion performance of a powder metallurgical aluminum alloy in aeronautical environments was studied for both as sintered and heat treated states. Sintered samples were obtained by uniaxial pressing of an Al-Cu-Mg prealloyed powder followed by liquid phase sintering. The heat treatments applied were T4 and T6. Corrosion behaviour was assessed by means of potentiodynamic polarization. Results for the equivalent commercial wrought counterpart, AA2024-T3, are also presented for comparison. Similar corrosion performance was observed for both as sintered and AA2024-T3 samples, while corrosion resistance of the PM materials was improved by the heat treatment, especially in the T4 state.
Contreras Jose M.,Jimenez-Morales Antonia,Torralba Jose M. 한국분말야금학회 2006 한국분말야금학회 학술대회논문집 Vol.2006 No.1
The MIM technology is an alternative process for fabricating near net shape components that usually uses gas atomised powders with small size (< 20 μm) and spherical shape. In this work, the possibility of changing partially or totally spherical powder by an irregular and/or coarse one that is cheaper than the former was investigated. In this way, different bronze 90/10 components were fabricated by mixing three different types of powder, gas and water atomised with different particle sizes, in order to evaluate how the particle shape and size affect the MIM process.
Modification of Low Alloyed Steels by Manganese Additions
Sicre-Artalejo J.,Campos M.,Torralba JM 한국분말야금학회 2006 한국분말야금학회 학술대회논문집 Vol.2006 No.1
The present study examines the sintering behaviour and effect of manganese addition both mechanically-blended and mechanically alloyed on Cr-Mo low alloyed steels to enhance the mechanical properties. Mn sublimation during sintering provides some specific phenomena which facilitate the sintering of alloying elements with high oxygen affinity. First step is the optimization of milling time to attain a master alloy with 50% of Mn which is diluted in Fe-1.5Cr-0.2Mo water atomized prealloyed powder by normal mixing. These mixtures are pressed to a green density of 7.1 g/cm3 and sintered at 1120 ºC in 90N2-10H2 atmosphere.
José María Hinojo,Clara Luján-Martínez,Antonio Torralba,Jaime Ramírez-Angulo 한국전자통신연구원 2017 ETRI Journal Vol.39 No.3
A new internally compensated low drop-out voltage regulator based on the cascoded flipped voltage follower is presented in this paper. Adaptive biasing current and fast charging/discharging paths have been added to rapidly charge and discharge the parasitic capacitance of the pass transistor gate, thus improving the transient response. The proposed regulator was designed with standard 65-nm CMOS technology. Measurements show load and line regulations of 433.80 µV/mA and 5.61 mV/V, respectively. Furthermore, the output voltage spikes are kept under 76 mV for 0.1 mA to 100 mA load variations and 0.9 V to 1.2 V line variations with rise and fall times of 1 µs. The total current consumption is 17.88 µA (for a 0.9 V supply voltage).
[ ] System: Structural Study of the Influence of Luminescence Center Concentration
Rabanal M.E.,Gomez L.,Khalifa A.,Mancic L.,Milosevic O.,Torralba J.M. 한국분말야금학회 2006 한국분말야금학회 학술대회논문집 Vol.2006 No.1
The influence of doping on the structural and morphological properties of the phosphor system, obtained ultrasonically via Spray Pyrolysis from common gadolinium and europium nitrate solutions, was studied. The particle morphology, crystalline and chemical structure were studied by XRD, SEM and EDS. TEM was applied in order to identify the structure and growth of "primary nanoparticles" and determine the presence of domains locally affected by "Moires Frames" and "Crystallite Size". The SADP allows determining the presence of a polycrystalline material with two phases in the "as-prepared" samples, and only an Ia3 phase along the thermal treatment.
Matula G.,Dobrzanski L.A.,Kloc A.,Herranz G.,Varez A.,Levenfeld B.,Torralba J.M. 한국분말야금학회 2006 한국분말야금학회 학술대회논문집 Vol.2006 No.1
Based on the comparison of structures and properties of the HS6-5-2 high speed steels made with the powder injection moulding method, pressureless forming, compacting and sintering, and commercial steels made with the ASEA-STORA method, fine carbides spread evenly in the steel matrix were found in the structure of all tested high-speed steels in the sintered state. The steels made with the pressureless forming method are characteristic of the lowest sintering temperature and the highest density, resulting from the high carbon concentration coming from the binding agent degradation.