http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
Rousseau, A.,Saglini, S.,Jakov, M.,Gray, D.,Hardy, K. The Korean Society of Automotive Engineers 2003 International journal of automotive technology Vol.4 No.1
The Center for Transportation Research at the Argonne National Laboratory (ANL) supports the DOE by evaluating advanced automotive technologies in a systems context. ha has developed a unique set of compatible simulation tools and test equipment to perform an integrated systems analysis project from modeling through hardware testing and validation. This project utilized these capabilities to demonstrate the trade-off in fuel economy and Oxides of Nitrogen (NOx) emissions in a so-called ‘pre-transmission’ parallel hybrid powertrain. The powertrain configuration (in simulation and on the dynamometer) consists of a Compression Ignition Direct Ignition (CIDI) engine, a Continuously Variable Transmission (CVT) and an electric drive motor coupled to the CVT input shaft. The trade-off is studied in a simulated environment using PSAT with different controllers (fuzzy logic and rule based) and engine models (neural network and steady state models developed from ANL data).
Rousseau, P.G.,du Toit, C.G.,Jun, J.S.,Noh, J.M. North-Holland Pub. Co 2015 Nuclear engineering and design Vol.291 No.-
The GAMMA+ and Flownex codes are both based on a one-dimensional flow network modelling approach and both can account for any complex network of different heat transfer phenomena occurring simultaneously. However, there are notable differences in some of the detail modelling aspects, such as the way in which the convection in the reactor cavity is represented. Despite this, it was found in the analyses of the air-cooled RCCS system that the results provided by the two codes compare very well if similar input values are used for the pressure drop coefficients, heat transfer coefficients and view factors. The results show that the radiation heat transfer comprises the bulk of the total rate of heat transfer from the RPV surface. It is also shown that it is possible to obtain a stable and sustainable steady-state operational condition where the flow is in the reverse direction through the RCCS standpipes, resulting in excessively high values for the concrete wall temperature. It is therefore crucial in the design to ensure that such a flow reversal will not occur under any circumstances. In general the good comparison between the two codes provides confidence in the ability of both to correctly solve the fundamental conservation and heat transfer relations in an integrated manner for the complete RCCS system. Provided that appropriate input values are available, these codes can therefore be used effectively to evaluate the integrated performance of the system under various operating conditions. It is shown here that the RCCS should remain functional and continue to provide sufficient cooling even for very high blockage ratios at the inlet to the riser ducts, which supports the safety case.
Damage prediction in the vicinity of an impact on a concrete structure: a combined FEM/DEM approach
Jessica Rousseau,Emmanuel Frangin,Philippe Marin,Laurent Daudeville 사단법인 한국계산역학회 2008 Computers and Concrete, An International Journal Vol.5 No.4
This article focuses on concrete structures submitted to impact loading and is aimed at predicting local damage in the vicinity of an impact zone as well as the global response of the structure. The Discrete Element Method (DEM) seems particularly well suited in this context for modeling fractures. An identification process of DEM material parameters from macroscopic data (Young’s modulus, compressive and tensile strength, fracture energy, etc.) will first be presented for the purpose of enhancing reproducibility and reliability of the simulation results with DE samples of various sizes. The modeling of a large structure by means of DEM may lead to prohibitive computation times. A refined discretization becomes required in the vicinity of the impact, while the structure may be modeled using a coarse FE mesh further from the impact area, where the material behaves elastically. A coupled discrete-finite element approach is thus proposed: the impact zone is modeled by means of DE and elastic FE are used on the rest of the structure. The proposed approach is then applied to a rock impact on a concrete slab in order to validate the coupled method and compare computation times.
A. ROUSSEAU,S. SAGLINI,M. JAKLOV,D. GRAY,K. HARDY 한국자동차공학회 2003 International journal of automotive technology Vol.4 No.1
The Center for Transportation Research at the Argonne National Laboratory (ANL) supports the DOE by evaluating advanced automotive technologies in a systems conlext. ANL has developed a unique set of compatible simulation tools and test equipment to perform an integrated systems analysis project from modeling through hardware testing and validation. This project utilized these capabilities to demonstrate the trade-off in fuel economy and Oxides of Nitrogen (NOx) emissions in a so-called 'pre-transmission' parallel hybrid powertrain. The powertrain contiguration (in simulation and on the dynamometer) consists of a Compression Ignition Direct Ignition (CIDI) engine. a Continuously Variable Transmission (CVT) and an electric drive motor coupled to the CVT input shaft. The trade-off is studied in a simulated environment using PSAT with different controllers (fuzzy logic and rule based) and engine models (neural network and steady state models developed from ANL data),<br/>
The Bilateral Cooperation between South Korea and Canada: Norms in Reality in Environmental Politics
이무성,김형민,David L. Rousseau 한국학술연구원 2013 Korea Observer Vol.44 No.1
Unlike previous decades, which stressed economic rationales in envisaging national environmental policies, Canada and South Korea have started to recognize each other as partners in environmental cooperation in the last twenty years. Canada seeks to preserve the environment at several critical junctures, while Korea has ardently pursued “low carbon, green growth” since the inauguration of the Lee administration in 2007. These two competing views can be summarized as the logics of consequentialism and appropriateness merit thorough explanations, respectively. With these logics in mind, this paper asks to what extent and under which conditions normative decision contributes to enhancing the bilateral relations. By doing so, the paper argues that the evolution of bilateral environmental cooperation can be attributed to ideational as opposed to material concerns. This contention is examined with particular reference to the two countries’ internal governance structure for environmental policy and the evolution of global environmental politics and governance.
N. KIM,H. LOHSE-BUSCH,A. ROUSSEAU 한국자동차공학회 2014 International journal of automotive technology Vol.15 No.2
Owing to ever more stringent regulations and customers’ expectations, auto manufacturers have beenconsidering numerous technology options to improve vehicle fuel economy. One of these is transmission technology, whichhas been shown to be one of the most cost-effective technologies. Over the past few years, transmissions have significantlyevolved and have impacted both performance and fuel efficiency. As one of the advanced tranmissions, the dual clutchtransmission (DCT) is the first automatic transmission to provide better efficiency than manual transmissions. DCTs providereduced shift shocks and better driver comfort in addition to higher top speeds and torques. In this paper, a model and shiftingcontroller for the DCT are developed in the vehicle systems context using Autonomie, a model-based vehicle simulation tool. Finally, the Autonomie DCT model and control strategy are validated using vehicle test data from Argonne’s AdvancedPowertrain Research Facility.
Audrey Petit,Jean-Baptiste Fassier,Sandrine Rousseau,Philippe Mairiaux,Yves Roquelaure 대한직업환경의학회 2015 대한직업환경의학회지 Vol.27 No.-
Several clinical practice guidelines related to the assessment and management of low back pain (LBP) have been published with varied scopes and methods. This paper summarises the first French occupational guidelines for management of work-related LBP (October 2013). There main originality is to treat all the three stages of primary, secondary and tertiary prevention of work-related LBP. The guidelines were written by a multidisciplinary working group of 24 experts, according to the Clinical Practice Guidelines method proposed by French National Health Authority, and reviewed by a multidisciplinary peer review committee of 50 experts. Recommendations were based on a large systematic review of the literature carried out from 1990 to 2012 and rated as strong (Level A), moderate (B), limited (C) or based on expert consensus (D) according to their level of evidence. It is recommended to deliver reassuring and consistent information concerning LBP prognosis (Level B); to perform a clinical examination looking for medical signs of severity related to LBP (Level A), encourage continuation or resumption of physical activity (Level A), identify any changes in working conditions and evaluate the occupational impact of LBP (Level D). In case of persistent/recurrent LBP, assess prognostic factors likely to influence progression to chronic LBP, prolonged disability and delayed return to work (Level A). In case of prolonged/repeated sick leave, evaluate the pain, functional disability and their impact and main risk factors for prolonged work disability (Level A), promote return to work measures and inter professional coordination (Level D). These good practice guidelines are primarily intended for professionals of occupational health but also for treating physicians and paramedical personnel participating in the management of LBP, workers and employers.