http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
李貞碩,張殷永,金元厚,方孝昌 한국항공대학교 1991 論文集 Vol.29 No.-
MLS(Microwave Landing System)는 어떤 활주로 상황에서도 기종에 관계없이 계기착륙이 필요한 항법정보를 정확하고 신롸성있는 상태에서 넓은 운용범위를 갖게되는 시스템으로서 ILS보다 장비기술 및 운용면에서 우수한 것으로 입증되었으며, 공항의 장애물과 악지형의 영향에 따라 유도특성이 방해받더라도 시스템의 가용성에는 제한이 없도록한 특징이 있다. 본 논문에서는 기존의 ISL의 접근절차로서는 불가능했던 비표준 지형과 평행 활주로에서 MSL를 이용한 접근 유도시 활주로 중심선에 대한 접근 오차 한계를 계산하고 기준 활주로와 평행 활주로 각각에 대한 접근유도시 거리오차를 산출하여 MSL를 이용한 정밀 접근유도 상태를 검토하였다. 그 결과 MSL는 비표준 지형 및 평행 활주로에서도 5NM이내의 거리에서는 접근오차가 0.1%(0.16NM)이내를 유지하여 ICAO 기준을 만족함으로써 규정상의 접근유도가 가능함을 알수 있었다. The MLS was followed by definition of a signal-in-space having the accuracy, reliability and coverage to aeronautics needs for all type of aircraft at all runway suitable for terminal instrument procedures. MLS has been demonstrated to be superior to ILS from both technical and operational capabilities. Even at runway where ground terrain and airport obstacles prevent standard split-site installations, the availability of MLS will not be limited. In this thesis, the range error and limitted error bound of a computed centerline approach is derived and identified in order to solve the problems of percision approach guidence at non-standard sitin gand parallel runway. As the result, it is known that the MLS is able to approach guidence with 0.1%(0.16NM) limited range error at non-standard siting and parallel runway within 5NM.
음전하를 띤 Microsphere 에 의한 정전기적 반발력이 정밀여과에서 투과 플럭스에 미치는 영향 고찰
박정민,최성욱,방시원,함승주,김중현,김우식 한국화학공학회 2001 Korean Chemical Engineering Research(HWAHAK KONGHA Vol.39 No.6
본 연구에서는 일정 압력하에서 음전하를 띤 microspheres의 정전기적 반발력에 따른 투과 플럭스의 변화에 관하여 고찰하였다. Microsphere의 정전기적 반발력에 관한 영향을 관찰하기 위해 표면전하 밀도(N_c: 0.45, 5.94, 10.25)가 각각 다른 poly(Styrene/Methacrylic acid) microspheres를 제조하였다. 교반속도는 300, 400, 600 rpm, 이온강도는 0.1, 0.01, 0.001로 변화시켜 실험하였다. 투과 플럭스는 표면전하밀도, 교반속도, 이온강도에 큰 영향을 받음을 알 수 있었으며, 투과 플럭스는 표면전하밀도가 클수록, 교반속도가 증가할수록, 이온강도가 작을수록 증가함을 알 수 있었다. 교반속도가 크면 막표면의 농도분극층의 두께가 얇아지기 때문에 투과 플럭스는 증가한다. 이온강도가 작을수록, 표면전하밀도(surface charge density)가 클수록 투과 플럭스가 커지는 원인은 microspheres의 정전기적 이중 층의 두께가 두꺼워짐에 따라 입자 사이의 거리가 멀어져 공극률(porosity)이 커지기 때문이다. 정상상태 플럭스 자료로부터 비 저항 정의식을 이용하여 케이크층의 공극률을 구할 수 있었다. 전하를 나타내지 않는 polystyrene microspheres의 입자크기가 480㎚일 때 농도분극 층의 이론적인 공극률은 0.211이었고, microspheres의 표면이 methacrylic acid로 완전히 개질된 것은 비 저항정의식에 의해 3.04로 계산되었다. 또한 microspheres들간의 정전기적 상호작용력이 작아지면 농도분극층의 공극률도 줄어드는 것을 알 수 있었다. The effect of the surface charge density(N_c: 0.45, 5.94, 9.14 and 10.25) and the stirrer speed(300, 400 and 600 rpm) on the variation of permeate flux was investigated in a stirred cell filled with negatively charged microspheres under constant pressure. It was found that the permeate flux depended on the surface charge density, the ionic strength and the stirrer speed. High permeate flux was obtained in the condition of high surface charge density, low ionic strength and high stirrer speed due to the force of electrostatic interaction between microspheres. The porosity of a cake layer was calculated from the steady-state flux data. It was found that the reduction of porosity was due to a decrease in repulsive interaction between microspheres.
Craves병 환자에서 백혈구와 갑상선 조직의 HLA-DR β 유전자 부위의 비교
양인명,우정택,팽정령,서광식,김성운,김영설,김광원,최영길 경희대학교 유전공학연구소 1989 遺傳工學論文集 Vol.1 No.-
정상 갑상선세포에서는 HLA-DR 항원이 발현되지 않았으나, 그레이브스병 환자의 갑상선세포 표면에는 HLA-DR 항원이 발현됨이 보고되어, 이러한 현상은 이 질환의 자가면역 기전에 중요한 역할을 하고 있을 것으로 생각되고 있다. 한편 최근 DR이나 DQ 유전자의 상부 159kb 이내에는 이들의 발현을 조절하는 유전자가 존재함이 알려져 있고, 이 부위의 구조적인 변화로 인하여 DR DQ 유전자의 발현을 유도하는 여러 가지 핵내 인자들과 interferon-r 와 같은 외부인 자들이 보고되고 있다. 그러나 그레이브스병에서 이들 유전자 부위의 구조적인 변화에 관해서는 아직 보고가 없다. 이에 본 연구자 등은 이러한 가능성 여부를 규명하고자 2명의 전형적인 그레이브스병 환자의 수술 우 얻어낸 갑상선 조직에서 RNA를 분리한 우 DR β유전자를 소식자로 northem blotting을 하여 mRNA의 발현을 관찰하였으며, 말초혈액 백혈구와 갑상선 조직으로부터 분리된 DNA를 EcoRI BamHI. HindⅢ PvuⅡ TaqI, PstI등의 6가지 제한효소로 소화한 후 DR β유전자를 소식자로 하여 RFLP 양상을 비교한 결과, 환자 모두에서 mRNA의 발현이 관찰되었으나, 환자 모두에서 6가지 제한효소에 의한 RFLP 양상이 동일하였다. 이러한 결과는 Graves병 환자의 DR 유전자의 발현에 있어서 이 유전자 부위의 구조적인 변화가 관여할 가능성이 적음을 시사하는 사실이라고 사료되나 향후 더 많은 예와 더 많은 제한효소를 이용한 주시가 필요할 것이다. The requirement for major histocompatibility antigen class Ⅱ molecules in the recognition of antigen by helper T cells suggests that the expression of class Ⅱ antigen may be important in the initiation and prolongation of immunopathology. HLA class Ⅱ antigenes are expressed on the surface of thyrocytes of the patients with graves disease. The increased expression of class Ⅱgene can be induced by trans acting factor such as interferon However the possibility of rearrangement of their regulatory genes has not been explored so far. We studied the mRNA expression in the thyrocytes of 2 patients with Graves' disease and compared the restriction fragment length polymorphism (RFLP) between thyroid and peripheral leukocyte DNA. The prominent expression of mRNA was observed in the thyroid tissues of all the two patients. But we did not find any difference in RFLP pattern in both patients. These results suggest the possibility that the rearrangement of the regulatory gene located in the upstream of DR- β gene can be a role in expression of DR antigen is less likely.
Pang-Jung Liu,Yu-Chi Hsu,Ting-Yu Wei,Zhi-Yuan Hong 전력전자학회 2019 ICPE(ISPE)논문집 Vol.2019 No.5
This paper presents a dc-dc converter with selfregulated output voltage (SROV) and phase shift PWM (PSPWM) control methods for multiple LED strings. The LED driver is composed of a boost converter and dimmable current balancing regulators (CBRs). Compared with traditional linear current regulator, the CBR is adopted to reduce power consumption. To keep a designed constant voltage on the CBRs, the output voltage of the boost converter is dynamically adjusted with the SROV control method. It results in high efficiency and current balance of the CBRs and prevents output voltage oscillation. The PSPWM control is employed to mitigate the output current variation supplied by the boot converter, leading to smaller output transient ripple when the PWM dimming signals are changed. The CBRs and control circuits were fabricated with a 0.35-μm standard CMOS technology. The experimental results demonstrate the theoretical analysis of the proposed LED driver.
Pang, Nan-Sim,Jung, Il-Young,Yu, Yoon-Jung,Kum, Kee-Yeon 大韓齒科保存學會 2006 Restorative Dentistry & Endodontics Vol.31 No.2
본 연구의 목적은 첫째 임상에서 진료실에 노출된 가타파차 콘 표면의 오염 균종을 중합효소연쇄반응법(polymerase chain reaction, PCR)을 이용해 동정하고, 둘째 이들 세균으로 오염시킨 가타파차 콘에 대해 3 종의 소독제의 short-term sterilization효과를 비교하였다. 또한 이들 소독제에 5 분간 처리된 가타파차 콘 표면 성상의 변화를 주사전자현미경으로 관찰하였고 물성 변화, 특히 인장 강도와 연신률의 변화를 측정, 비교하고자 하였다. 진료실에 수 개월간 노출된 가타파차 콘 150개를 수거하여 배양지에 넣어 배양 후 universial primer를 사용한 PCR assay를 통해 오염 균종을 동정하였다. 실험실 상에서 이 균종을 다시 배양하여 소독된 가타파차 콘에 접종하고 1 주일간 배양한 후 3 종의 소독제 (5% NaOCl, 2% Chlorhexidine, ChloraPrep)에 1, 5, 10, 30 분간 short-term soaking후 각 소독제의 종류의 적용시간에 따른 멸균 효과를 turbidity test와 subculture를 이용하여 평가하였다. 또한 각 소독제에 5 분간 처리된 가타파차 콘 표면 성상의 변화를 주사전자현미경으로 관찰하였으며, 물성 변화를 평가하기 위해 Instron 5500을 이용하여 연신률 및 tensile strength를 측정한 후 통계학적 유의성 여부를 검증하였다. 중합효소연쇄반응법의 분석결과 19.4%의 가타파차 콘 이 오염된 것으로 나타났고 대부분이 Staphylococcus 계통이었으며, 3 종의 소독제 모두 이들 균종에 대해 1 분내에 멸균 효과를 나타냈다. 주사전자현미경상 NaOCl로 소독된 가타파차 콘 표면에는 cuboidal crystal 의 침전물이 전반적으로 관찰되었다. Tensile strength는 NaOCl군에서 다른 군에 비해 유의성 있는 증가를 보였으며 (p <0.05), elongation rate는 3 종의 소독제 모두 대조군에 비해 유의성 있는 증가를 보였으나 (p < 0.05), 특히 ChloraPrep군에서 가장 큰 증가를 보였다. 본 연구 결과 3 종의 소독제 모두 근관충전 전 가타파차 콘의 rapid sterilization을 위해 유용하게 사용할 수 있음을 시사한다. The purposes of this study were firstly to identify the microbial species on gutta-percha (GP) cones exposed at clinics using polymerase chain reaction, and secondly to evaluate the short-term sterilization effect of three chemical disinfectants. It also evaluated the alteration of surface texture and physical properties of GP cones after 5-min soaking into three chemical disinfectants. 150 GP cones from two endodontic departments were randomly selected for microbial detection using PCR assay with universal primer. After inoculation on the sterilized GP cones with the same microorganism identified by PCR assay, they were soaked in three chemical disinfectants : 5% NaOCl, 2% Chlorhexidine, and ChloraPrep for 1, 5, 10, and 30 minutes. The sterilization effect was evaluated by turbidity and subculture. The change of surface textures using a scanning electron microscope and the tensile strength and elongation rate of the GP cones were measured using an Instron 5500 (Canton). Statistical analysis was performed. Four bacterial species were detected in 29 GP cones (19.4%), and all the species belonged to the genus Staphylococcus. All chemical disinfectants were effective in sterilization with just 1 minute soaking. On the SEM picture of NaOCl-soaked GP cone, a cluster of cuboidal crystals was seenon the cone surface. The tensile strenght of NaOCl-soaked group was significantly higher than the other groups (p< 0.05). Alsi, all disinfectants significantly increased the elongation rate of GP cones compared to the fresh GP cone (p < 0.05). Present data demonstrate that three chemical disinfectants are useful for rapid sterilization of GP cone just before obturation.
홍정표 ( Jung Pyo Hong ),오정권 ( Jung Kwon Oh ),박주생 ( Joo Saeng Park ),한연중 ( Yeon Jung Han ),방성준 ( Sung Jun Pang ),김철기 ( Chul Ki Kim ),이전제 ( Jun Jae Lee ) 한국목재공학회 2015 목재공학 Vol.43 No.4
KS F 3020-침엽수구조용재 기준에 따라 국산 소나무(Pinus densiflora) 38 × 140 × 3600 mm 구조용 제재목 365개에 대하여 기계등급구분을 실시하고, 휨허용응력을 산출하여 현재 적용되는 KS기준허용응력과 비교 분석하였다. 휨허 용응력 계산을 위하여 5% 휨강도 하한값을 75% 신뢰수준의 비모수적 방법, 2-parameter 그리고 3-parameter Weibull 분포를 가정한 모수적 방법, 휨강도-휨탄성계수 직선회귀 방법, 총 4가지 분석방법을 사용하여 결정하였다. 기계등급 E8, E9, E10 만이 비모수적 방법의 통계 처리가 가능한 자료 수를 얻었으며, 휨강도-휨탄성계수 직선회귀 방법은 이론적으로 모든 등급에 대한 5% 하한값 결정이 가능함을 보여주었다. 결정된 등급별 휨허용응력은 기준허용응력에 비하여 모두 낮은 값을 나타내었으며 이것은 과소설계의 위험성이 있는 것으로 현행 기계등급구분체계의 문제점으로 파악되었다. 이러한 문제는 구조설계 신뢰성과 관련하여 반드시 개선되어야 할 것으로, 휨강도-휨탄성계수 조합 등급 도입이 필요할 것으로 생각되었다. 365 pieces of domestic 38 × 140 × 3600 mm Red pine structural lumber were machine graded conforming to a softwood structural lumber standard (KS F 3020). The allowable bending stresses calculated for each grade were compared with the values currently tabulated in the standard. Four calculation methods for lower 5th percentile bending stress were non-parametric estimation with 75% confidence level, 2-parameter and 3-parameter Weibull distribution fit, and bending modulus of rupture (MOR)-modulus of elasticity (MOE) regression based method. Only the data set of Grades E8, E9, and E10 were statistically eligible for the 5th percentile calculation. The MOR-MOE regression based method only was able to estimate the lower 5th percentile values theoretically for the full range of grades. The results showed that all allowable bending stresses calculated were lower than the design values tabulated in the standard. This implies that the current machine grading system has the pitfall of structural safety. Improvement in current machine grading system could be achieved by introducing the bending strength and stiffness combination grade system.
국내 기계등급구조재의 등급구분체계 및 기준설계값 결정방법 연구
홍정표 ( Jung Pyo Hong ),이전제 ( Jun Jae Lee ),박문재 ( Moon Jae Park ),여환명 ( Hwan Myeong Yeo ),방성준 ( Sung Jun Pang ),김철기 ( Chul Ki Kim ),오정권 ( Jung Kwon Oh ) 한국목재공학회 2015 목재공학 Vol.43 No.4
국내외 기계등급제재목(구조재 및 층재)의 등급기준 및 설계강도 산출방법을 비교 분석하고 국내 제재산업 실정을 고려한 평균 탄성계수(modulus of elasticity, 이하 MOE) 기준방법 적용을 제안하였다. 먼저 올바른 기계등급제재목 기준 정착을 위해 기계등급구조재와 기계등급층재의 공통점과 차이점을 설명하였다. 최소 고정 MOE 기준 등급을 사용하는 국내 기준은 등급구분에는 편리하나 휨강도(modulus of rupture, 이하 MOR) 예측과 자원이용도 측면에서는 효율성이 낮은 것으로 파악되었다. 해외에서 사용되는 평균 MOE 기준 방법은 초기 컴퓨터 기반 작동을 요구하나 MOR-MOE 직선회귀에 근거한 합리적인 MOR 예측과 품질관리 측면에서 효율성이 높은 것으로 분석되었다. 무엇보다도 현 국내 기계등급구조재 등급체계는 수종별 강도 특성을 반영하지 못하고 있다는 것이 가장 큰 문제점으로 분석되었으며 이러한 결과를 기반으로 MOR-MOE 직선회귀분석에 근거한 기계등급제재목 등급기준 및 기준설계값 산출방법 적용을 제안하였다. 이를 통하여 궁극적으로 부가가치가 높은 국산 기계등급구조재 생산 활성화를 이루고, 기계등급구조재의 층재 전용 가능에 따른 구조용 집성재 가격경쟁력 제고 효과를 얻을 수 있다고 사료되었다. Based on comparative studies on standards and grading procedures of machine graded lumber in Korea and other countries, this study proposed a procedure of determining the grade classification and design strengths of domestic machine graded lumber. Differences between machine stress rated lumber and E-rated laminations were detailed in order to clarify the need for the procedure improvement. To this improvement the use of average MOE requirement for grading was introduced instead of the fixed minimum MOE requirement which is currently used in the Korean standards. It was found that the fixed minimum MOE requirement method was easier for an inspector to grade but, less efficient as a strength predictor than the average MOE requirement method. The advantage of average MOE requirement method is statistically MOR-MOE regression-based MOR prediction and highly efficient in quality control though it requires a computer-aided operation system in an initial setup. A major weakness of the current Korean grading system was found that different strength characteristics depending on wood species were not reflected on the grade classification and the tabulated allowable design stress. The proposed procedures were developed taking advantages of respective merits of both methods and based on MOR-MOE regression analysis. Through this procedure, the grades of machine stress rated lumber should be revised to become interchangeable with E-rated lamination, which would be beneficial to the cost competitiveness of domestic machine graded lumber and glued laminated timber industry.