벡터값을 갖는 함수에 대한 MH1 적분에 관한 연구

은광식, 윤주한 충북대학교 과학교육연구소 2011 과학교육연구논총 Vol.27 No.1

본문 참고

GLASS/UP系 複合材料의 破壞에 미치는 NOTCH平徑의 影響

김귀식,박경석,오맹종,김주봉 濟州大學校工科大學附屬産業技術硏究所 1992 尖端技術硏究所論文集 Vol.3 No.-

This study is investigated by experimental method and FEM about the effect of notch root radious(ρ) on the fracture of GFRP. The smaller ρshowed the fracture behavior which was mainly caused by the propagation of the stable crack, but the fracture behavior in the larger ρwas mainly caused by the spread of damage. The experimental value of the nominal stress could be estimated by FEM simulation and the load-displacement curve could also be drawn. According to the results simulated damage zone by FEM, as the ρis smaller, the damage begin at low stress.

담배 個體群의 生態學的 硏究 : 第6報 個體群內 葉分布樣式 및 몇가지 形質에 미치는 栽植距離 및 密度의 影響 Part VI. The Effect of Plant Spacings and Density on the Leaf Distribution Pattern and on Some Agronomic Characteristics

申周植 충북대학교 엽연초연구소 1982 煙草硏究 Vol.9 No.-

This experiment was conducted to investigate the influence of plants density and spacings on the leaf azimuth, number and percentage of leaves oriented to the right angle to the row and parallel to the row, the degree of midrib curvature, and some other agronomic. Hicks(flue-cured tobacco) and Burley-21(Burley tobacco) were applied in this experiment. The results are summarized as follows. The leaf azimuth was influenced by plants density and spacings. The prefered azimuth of the leaves tended to be towards the direction of greater spacing. The percentage of leaves oriented to the right angle to the row is greater than that oriented parallel to the row. And the percentage of leaves oriented to the right angle to the row increased in the case of high density and narrow spacing between plants in a row. Hicks had more leaves haying curved than Burley-21 did. There was no correlation between the percentage of leaves having curved midrib and the percentage of leaves oriented parallel to the row. And these were no differences of the percentage of loaves having curved midrib according to plants density and spacings. In the cane of middle leaves, weight of leaf lamina, weight per unit leaf area, percentage of dry matter and specific weight were larger in the larger part of the lamina than in the smeller part of the lamina of loaves having curved midrib.

배·급수 시스템에서 부식방지제의 적용 평가 연구

우달식,문정기,구성은,최종헌,김주환,문광순 대한상하수도학회 2003 상하수도학회지 Vol.17 No.5

This study evaluated the effect of the corrosion inhibitors on the corrosion control performance in drinking water distribution system. A phosphate-zinc based inhibitor formulated was for the efficient corrosion control in drinking water distribution system. In a continuous-circulation test, 99% reduction in corrosion rate was achieved. The optimum concentration of the corrosion inhibitor was found to be 2.2㎎ PO₄/L. The effect of the corrosion inhibitor was significant for the pipes of carbon steel, galvanized steel and copper, but less for that of stainless steel. The corrosion inhibitor can be an effective cure for corrosion and red water problems by prevention the old pipes from further corrosion. Tap water in Mokpo and Kwangyang were more corrosive than the water in the rest of 4 other regions(Seoul, Pohang, Pusan, Puyeo). Tap water in Pusan was high in various ionic concentrations in general. The corrosion inhibitor reduced the corrosion rate by 76-94%, depending on the origin of the tap water.

담배個體群의 生態學的 硏究 : 第三報 담배의 葉型에 따른 葉面積 測定方法에 關한 硏究 III. Methods of Measuring Leaf Area of Tobacco according to Leaf Shape

申周植 충북대학교 엽연초연구소 1978 煙草硏究 Vol.5 No.-

This experiment was performed to study the methods of measuring the leaf area for the undetached leaf from the stem. According to leaf position and leaf shape, the relationship between precise leaf area (PLA) and leaf length×width (LL×LW) was analysed. In that relationship, leaf area coefficients (a) (PLA/LL×LW) were obtained. In addition to the above, some coefficients to correct the leaf area by leaf weight was obtained. The results are summarized as follows. 1.Coefficient (a) was varied according to leaf position and leaf shape index (LSI). The coefficient of the lower middle and upper leaves were 0.6464, 0.6527 and 0.6621 respectively. According to the LSI-I, the coefficient for the loaves below 45% in LSI-I was 0.6405, and that of the leaves above 45% was 0.6563. The average coefficient for all the leaves was 0. 2.The higher the LSI-III was, the higher the coefficient was. But the higher tnt SI-II was, the lower the coefficient was. 3.Six types of leaves was divided according to three LSI used in this experiment. Different types of leaves showed different value of coefficient. 4.In the relationship between the precise leaf area and the leaf area computed by leaf weight and weight of unit leaf area, regression coefficients and leaf area coefficients showed differences according to leaf position and leaf shape.

유한요소법에 의한 호안의 강제치환 형상에 관한 변형예측 및 현장계측

박춘식,장정욱,하주화 국립7개대학공동논문집간행위원회 2005 공업기술연구 Vol.5 No.-

This study used the finite element method analysis to estimate enforced replacement shapes and replacement depth. The data were expected to be used as the fundamental data of the design through the comparison with the results of the elastic wave exploration and investigation. The results of the research are summarized in the following. (1) After dividing the breakwater into 5models, on which elastic wave exploration was performed, the enforced replacement shape has been obtained by the finite element method. The result was satisfactory compared to the results of the elastic wave exploration. (2) The enforced replacement shapes of the breakwater were compared in different ways; in the design, in the elastic wave exploration in field and in this study. While the enforced replacement shape in the design is substantially different from that in elastic wave exploration in field, it turned out to be similar to the results of this research. (3)If an enforced replacement shape is standardized in configuration of breakwater, depth of soft soil and th value of soil property, it can be used as the standardized section in designing breakwaters.

Back Propagation 알고리즘을 이용한 산업용 로봇의 견실제어

윤주식,이희섭,윤대식,한성현 한국공작기계학회 2004 한국공작기계학회 춘계학술대회논문집 Vol.2004 No.-

Neural networks are works are used in the framework of sensor based tracking control of robot manipulators. They learn by practice movements the relationship between PSD(an analog Position Sensitive Detector) sensor readings for target positions and the joint commands to reach them. Using this configuration, the system can track or follow a moving or stationary object in real time. Furthermore, an efficient neural network architecture has been developed for real time learning. This network uses multiple sets of simple back propagation networks one of which is selected according to which division(corresponding to a cluster of the self-organizing feature map) in data space the current input data belongs to. This lends itself to a very training and processing implementation required for real time control.

播種期 및 育苗日數가 黃色種 담배의 初期生育 및 收量에 미치는 影響

申周植,盧載榮,裵吉寬,朴相一 충북대학교 엽연초연구소 1984 煙草硏究 Vol.11 No.-

This experiment was carried out to study the influence of different sowing time, seedling age (the degree of delayed setting) and seedlingbed materials on the growth and yield components of flue-cured tobacco. The variety applied was N.C. 2326, was sown on March 1,11,21 and 31. Those plants were transplanted on the seeding bed mixed humus with sand at the ratio of humus 9 : sand 1 and humus 3: sand 7, 25 days after sowing. Seedlings were grown for 40, 50, 60 and 70 days (from sowing to setting) on the seed bed and seedling bed, and set on the pots (1/5,000a) in the vinyl house. The results obtained were as forlows . 1.The amount of growth of seedlings increased by late sowing and delayed setting. 2.Until the time before the maximum growth stage after setting, stem heigth was larger in the plots of late sowing and delayed setting. After the middle part of maximum growth stage, the earner the sewing time was, the more remarkable the influence of seedling age on the stem elongation was and the larder the seedling age was, the more remarkable the influence of sowing time on the stem elongation was. 3.Stem diameter was large in the plot to late sowing until the early part of maximum growth stage but after the middle part of maximum growth stage the diameter was large in the plants sown at March 11 and March 21. 4.The number of leaves per plant increased by late sowing and delayed setting shown significant difference after maximum growth stage. 5.Late setting made the stem height high and number of leaves per plant more. The size of largest leaf was small in the plot of early sowing and large in the plot set after May 10. 6.It takes more days to reach a topping time from sowing and setting in the case of early sowing and early setting. 7.In early sowing plots, the leaf area of lugs and cutlers decreased by younger seedling age, and in late sowing plots, that decreased by older seedling age. The leaf area of leaf and tip at different treatments showed similar results, but in the plots sown at March 11 and 21, largest leaf was shown in the plot of 50- day seedlings. The area of green tip decreased by late seeding and delayed setting. As a result of theses the plant type showed sylindrical in the plot of early sowing and younger seedling age, and cone shape in the plot of late sewing and older seedling age. 8.The earlier the sowing time and the younger the seedling age were, the heavier the weight of unit leaf area of lugs and cutters, but there were little influences of different sowing time and seedling age on the weight of unit leaf area of leaf, tip and green tip. The percentage of dry matter showed similar tendency to the results of weight of unit leaf area. 9.Late sowing (March, 31) decreases the weight of a cured leaf. Weight of cured cutter was largest in the plots sowing March 1 and that of leaf tip and green tip was largest in the plots sowing March 11 and March 21. The weight of cured lugs was largest in 40 and 50-day seedlings, and that of tip and green tip was largest in 50-day seedlings. There were little differences of weight of a cutter and leaf among the treatments of different seedling age. 10.In 40- day seedlings, the area and weight of leaves per plant increased by late sowing, and in 70-day seedlings, those increased by early sowing. In 50 and 60-day seedlings, those were highest in the plots sown at March 11 and March 21. Largest weight and area of leaves per plant was shown in the plot set on May 10, and the plots set on April 10, and June 1 showed significantly low weight of loaves per plant. 11.Late sowing and older seedling age increased the leaf thickness of those leaves. Different sowing time and the seedling age did not influence on the leaf area contraction ratio and leaf thickness of leaf, tip and green tip. 12.There were significantly negative correlation between leaf area of lug and cutter and weight per unit leaf area, percentage of dry matter and leaf thickness of the lug and cutters, but no correlation between those characters of leaf, tip and green tip. Weight per unit leaf area correlated positively with percentage of dry matter and specific leaf weight in all stalk position. In the lug and cutter, weight per unit leaf area correlated positively with leaf thickness and negatively with leaf area contraction between weight per unit leaf area and leaf area contraction ratio. There were negative correlation between leaf thickness and leaf area contractions of lugs and cutters, and no correlation between those characters of leaf, tip and green tip. 13.There were not significant effects of seedling bed materials applied in this experiment on the growth after setting and yield components.

회전식 nickel-titanium file을 이용한 유치의 근관치료

서주희,이광희,김대업,양계식 大韓小兒齒科學會 2001 大韓小兒齒科學會誌 Vol.28 No.4

유치의 근관치료에서 치수절제술은 실활된 유치를 치열궁내에 유지하기 위해 치관과 근관부분의 괴사된 치수조직을 완전하게 제가하는 것을 말한다. 이 술식은 감염된 치수의 세균을 감소시키는 것을 목적으로 하며, 다양하고 불규칙한 유치 근관의 형태가 주된 장애 요소로 작용한다. 더욱이 비협조적인 어린이의 경우에는 오랜 시간동안 정교한 시술을 하기가 곤란하다. 최근 들어 근관치료시에 회전식 기구를 이용하여 근관형성을 하는 장비들이 많이 개발되었으며 저속전기 모터에 회전식 NiTi file을 이용한 술식이 많이 사용되고 있다. 본 증례에서는 회전식 NiTi file과 전기모터를 이용하여 유구치의 근관치료를 시도하였다. 치수강을 개방하고 치관부 치수를 제거한 후 잠정적 작업장을 측정하였으며 적절한 NiTi file을 선택하여 잠정적 작업장까지 crown-down 방법으로 점차적으로 형성하였다. 수용 file로 근단부 도달 및 성형을 하고 전체적인 마무리를 하여 Vitapex로 충전하여 양호한 결과를 얻었기에 보고하는 바이다. The pulpectomy or root canal treatment on primary teeth is to be done when there is evidence of chronic in flammation or necrosis in the radicular pulp. Due to the tortuous and ribbon-shaped anatomy of the primary teeth, the instrumentation of endodontic hand files and barbed broaches is not an easy procedure. Recently, many automatic Ni-Ti rotary instruments have been developed and has made endodontic treatment easier and faster. This report describes two cases of root canal treatment on primary molars using Ni-Ti rotary files. The cervical constricture was eliminated by the crown-down method, as smaller file proceeded unhindered into the apical third of the canal. In addition, the crown-down technique enhanced the efficacy of the endodontic irrigant. The use of rotary instrumentation for primary teeth seemed to be a more effective way to debride the uneven walls of primary teeth.

관절염으로 발현한 재발성 다발성 연골염 1례

엄민식,박원우,서승철,이진호,조주연,최혜영,이찬희,임소덕 白中央醫療院 2005 仁濟醫學 Vol.26 No.1

Relapsing polychondritis is an uncommon multisystemic disease which is characterized by recurrent episodes of inflammation and progressive destruction of cartilaginous tissue. The cause of relapsing polychondritis is unclear and suspected to be autoimmune pathophysiology. It involves cartilage of nose, vertebra, trachea, peripheral joint as well as structures of eye, heart, blood vessels or inner ear. Auricular chondritis is present in almost all patients, and multiple arthritis, nasal chondritis, saddle nose, eye involvement, laryngotracheal involvement and skin manifestations are also present. We report a case of relapsing polychondritis presented a arthritis with review of literatures.