http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
조우석 ( Woo Sug Cho ),이영진 ( Young Jin Lee ),좌윤석 ( Yoon Seok Jwa ) 大韓遠隔探査學會 2003 大韓遠隔探査學會誌 Vol.19 No.4
본 논문은 수동센서인 항공카메라와 능동센서인 레이저스캐너의 상호 보완적인 특징을 이용하여 지표면에 존재하는 다양한 지형지물 중 건물을 자동으로 추출하는 알고리즘에 대한 연구이다. 제안하는 건물추출 알고리즘은 처리 단계별로 사용되는 데이터의 형태에 따라 point level process, polygon level process, parameter space level process의 세 단계로 나눌 수 있다. 첫 번째 단계인 point level process에서는 LIDAR의 점 데이터에서 과대오차를 제거하고 건물후보점들을 추출하여 같은 특성을 갖는 점들을 모아 폴리곤을 제작한다. 두 번째 단계에서는 면적조건과 circularity를 이용하여 수목 폴리곤을 제거하고, 건물 폴리곤 사이의 포함관계를 정립한다. 마지막 단계에서는 이전 단계의 최종 건물 폴리곤을 공선조건식을 이용하여 항공사진 위에 투영하고 모폴로지 필터링을 통해 탐색영역을 제한한 후, Hough 변환의 파라미터 공간에서 다양한 가정과 제약조건을 이용하여 건물의 외곽선을 추출한다. 제안된 알고리즘에 의해 자동으로 추출된 건물 외곽선의 정확도를 검증하기 위하여 건물 모서리점의 3차원 좌표를 결정하였고, 이를 수치사진측량시스템에서 관측한 결과와 비교하였다. 실험결과 각 건물 모서리점의 평균제곱근오차는 X, Y, Z 각 방향으로 ±8.1cm, ±24.7cm, ±35.9cm로 나타났다. This paper presents an algorithm that automatically extracts buildings among many different features on the earth surface by fusing LIDAR data with panchromatic aerial images. The proposed algorithm consists of three stages such as point level process, polygon level process, parameter space level process. At the first stage, we eliminate gross errors and apply a local maxima filter to detect building candidate points from the raw laser scanning data. After then, a grouping procedure is performed for segmenting raw LIDAR data and the segmented LIDAR data is polygonized by the encasing polygon algorithm developed in the research. At the second stage, we eliminate non-building polygons using several constraints such as area and circularity. At the last stage, all the polygons generated at the second stage are projected onto the aerial stereo images through collinearity condition equations. Finally, we fuse the projected encasing polygons with edges detected by image processing for refining the building segments. The experimental results showed that the RMSEs of building comers in X, Y and Z were 8.1cm, 24.7cm, 35.9cm, respectively.
전기전도성을 가지는 매크로다공성 알루미노실리케이트-탄소 복합체 제조
최광민,조우석,김종영,정종열,백승우,이규형,Choi, Kwang Min,Cho, Woo-Seok,Kim, Jong-Young,Jung, Jong-Yeol,Baik, Seung-Woo,Lee, Kyu Hyoung 한국전기전자재료학회 2017 전기전자재료학회논문지 Vol.30 No.2
Recently, macroporous ceramic materials with high electrical conductivity and mechanical strength are urgently needed for semiconductor and display manufacturing devices. In this work, we obtained electro-conducting macroporous aluminosilicate ceramics having surface resistivity of 108~1,010 ohm by dispersing electro-conducting carbon in ceramic matrix. By addition of 0.5~3.0 wt% frit glass, chemical bonding between grains was strengthened, and flexural strength was enhanced up to 160 MPa as a result. We evaluated the characteristics of present ceramics as vacuum chuck module for liquid crystal display display manufacturing devices.
김진호,조우석,황광택,한규성,Kim, Jin-Ho,Cho, Woo-Seok,Hwang, Kwang-Taek,Han, Kyu-Sung 한국재료학회 2017 한국재료학회지 Vol.27 No.2
Recently, there have been many efforts to establish suitable processes for recycling fly ash, which is produced in thermal power plants and which poses serious environmental problems. Use of fly ash as a major ingredient of ceramic tiles can increase fly ash utilization, as well as reduce the cost of raw materials in ceramic tile production. In this study, the effects of fly ash addition on ceramic tile properties such as bending strength, water absorption and porosity were investigated. A manufacturing process of ceramic tile was developed for utilization of fly ash with high carbon content. In this approach, it is important to hold the ceramic tiles at a temperature that is sufficient for carbon oxidation, before the pores supplying oxygen to the inside of the ceramic tile are sealed. Ceramic wall tiles were manufactured with 0-40wt% of fly ash addition. The water absorption and porosity of the fired body were slightly changed with increasing fly ash content up to 30wt% and decreased with greater amounts of fly ash addition. The bending strength of ceramic tile including 10wt% fly ash increased, reaching a level comparable to that of ceramic tile without fly ash.
박영수,위인희,조우석,김진호,황광택,Park, Young-Soo,Wui, In-Hee,Cho, Woo-Seok,Kim, Jin-Ho,Hwang, Kwang-Taek 한국결정성장학회 2012 한국결정성장학회지 Vol.22 No.6
알루미늄 에칭 폐액으로부터 boehmite(AlOOH) 분말을 합성하였다. 폐액에서 침전되어 있는 결정상은 gibbsite ($Al(OH)_3$)였으며, 산을 이용하여 pH를 조절한 결과 pH가 7~8 영역에서 boehmite 결정상이 얻어졌다. 침전 분말에 남아 있는 Na 이온을 제거하고자 세척공정을 진행하여 boehmite 분말을 얻었다. 합성한 분말의 평균입경은 약 40 nm이었다. 또한 열처리 온도가 증가함에 따라 boehmite는 ${\gamma}-Al_2O_3$와 ${\delta}-Al_2O_3$, ${\Theta}-Al_2O_3$를 거쳐 ${\alpha}-Al_2O_3$ 결정상으로 상전이가 일어났다. Boehmite (AlOOH) powder was synthesized using waste aluminium etching solution. In waste solution, precipitated phase was gibbsite ($Al(OH)_3$), and boehmite (AlOOH) phase was obtained at pH of 7 and 8 controlled by addition of acid. Boehmite powder was obtained by washing process to remove the Na ion in precipitated solution. Mean particle size of obtained powder was 40 nm. Boehmite phase transformed to ${\alpha}-Al_2O_3$ phase via ${\gamma}-Al_2O_3$, ${\delta}-Al_2O_3$, and ${\Theta}-Al_2O_3$.
디지털 프린팅용 세라믹 잉크의 유약표면 인쇄적성 및 특성평가
김진호,황광택,조우석,한규성,Kim, Jin-Ho,Hwang, Kwang-Taek,Cho, Woo-Seok,Han, Kyu-Sung 한국결정성장학회 2017 한국결정성장학회지 Vol.27 No.5
$1000^{\circ}C$ 이상의 고온에서도 안정적인 발색 특성을 보이는 세라믹 잉크를 활용한 디지털 프린팅 기술은 우수한 내구성을 가지는 제품을 다양한 디자인을 적용하여 생산할 수 있는 친환경 공정이라는 장점으로 인해 최근 관심이 높아지고 있다. 특히 건축용 세라믹 타일 산업에서 잉크젯 프린팅 기술 도입을 통한 디지털 공정으로의 전환은 점점 가속화되고 있으며, 이와 관련된 프린팅 시스템 및 고온발색 세라믹 잉크에 관한 연구가 활발히 진행되고 있다. 본 연구에서는 세라믹 타일의 표면 유약층에서 고온발색 세라믹 잉크의 인쇄적성을 분석하였다. 디지털 4원색인 Cyan, Magenta, Yellow, Black 색상의 고온발색 세라믹 잉크가 프린팅된 세라믹 타일의 표면 및 단면의 미세구조를 분석함으로써 세라믹 잉크의 종류에 따른 인쇄특성에 대해 비교하였다. 또한 고온 열처리 공정이 필수적으로 요구되는 세라믹 소재의 특성상 잉크젯 프린팅 후 세라믹 잉크 패턴의 열처리 공정에 따른 거동변화에 관하여 고찰하였으며, 세라믹 타일 유약층에서 세라믹 잉크의 인쇄적성은 미세구조 및 고온 소성 과정에 큰 영향을 받고 있음을 확인하였다. Digital ink-jet printing technology using ceramic ink, which is thermally stable at high temperature above $1000^{\circ}C$, has an advantage of eco-friendly process applicable to manufacturing products with an excellent durability and various designs. Recently, replacement from conventional manufacturing process to digital process using ink-jet printing technique has been significantly accelerated in ceramic tile industry. In this study, we investigated ink-jet printability of ceramic ink on ceramic tile. Cyan, magenta, yellow, black ceramic inks, which are digital primary color of ink-jet printing, were printed on glazed surface of ceramic tiles, and their printabilities were comparatively analyzed. High temperature sintering process is generally required for manufacturing ceramic products, thus effect of sintering process on printed pattern of ceramic ink was also investigated by analyzing ink penetration depth and ink dot area.