Basal slip (0001)1/3 <1120> dislocation in sapphire ($\alpha$-$Al_2$$O_3$) single crystals Part I: Dislocation velocity

윤석영,이종영,Yoon, Seog-Young,Lee, Jong-Young Materials Research Society of Korea 2001 한국재료학회지 Vol.11 No.3

사파이어 ($\alpha$-$Al_2$$O_3$) 단결정에 있어 basal slip (0001)1/3<1120>의 전위속도를 4점 곡강도를 이용하여, 측정하였다. 이 곡강도는 온도 $1200^{\circ}C$ 에서 $1400^{\circ}C$ 그리고 응력은 90MPa, 120MPa, 160MPa에서 행하여졌다. 전위속도는 4 점굽힘 시편의 굽힘변위속도에 의해 구하여졌다. 얻어진 전위속도를 이용하여 전위속도의 온도 및 응력 의존성에 대해 검토하였다. 전위속도의 온도의존성을 이용하여 basal slip 전위속도를 위한 활성화에너지를 구하였으며, 그 값은 대략 2.2$\pm$0.4eV이었다. 한편, 전위속도의 응력의존성을 나타내는 응력지수 m은 2.0$\pm$0.2이었다. The basal slip (0001)1/3<1120 > dislocation velocity in sapphire ($\alpha$-$Al_2$$O_3$) single crystals was measured by four-point bending test. The bending experiment was carried out in the temperature range from 120$0^{\circ}C$ to $1400^{\circ}C$ at various engineering stresses 90MPa, 120MPa, and 150MPa. The velocity of such dislocations was estimated from the bending displacement rate of the four-point bend sample. The dependence of temperature and stress in dislocation velocity was investigated. The activation energy for dislocation velocity was determined to be about 2.2$\pm$0.4eV. In addition, the stress exponent (m) describing the stress dependence of dislocation velocities was in the range of 2.0$\pm$0.2.

반용융상태에서 가압용침에 의한 재료의 구조화와 복합화

윤석영,강정윤,Yoon, Seog-Young,Kang, Chung-Yun 대한용접접합학회 2006 대한용접·접합학회지 Vol.24 No.5

마이크로파에 의한 생분해성 β-TCP/PLGA 복합체의 제조시 β-TCP 첨가량에 따른 영향

진형호,민상호,박홍채,윤석영,Jin, Hyeong-Ho,Min, Sang-Ho,Park, Hong-Chae,Yoon, Seog-Young 한국재료학회 2006 한국재료학회지 Vol.16 No.1

Biodegradable $\beta$-tricalcium phosphate ( $\beta$-TCP)/poly(lactide-co-glycolide) (PLGA) composites were synthesized by in-situ polymerization with microwave energy. The influence of the $\beta$-TCP content in $\beta$-TCP/PLGA composites on the molecular weight, crystallinity, microstructure and mechanical properties was investigated. As the molecular weight of composites decreased, the $\beta$-TCP content increased up to 10 wt.%, while the excess addition of the $\beta$-TCP content above 10 wt.% the molecular weight increased with increasing of the $\beta$-TCP content. This behavior would be due to the superheating effect or nonthermal effect induced by microwave energy. It was found that the bending strength and Young's modulus of the $\beta$-TCP/PLGA composites was proportional to the molecular weight of PLGA. The bending strength of the $\beta$-TCP/PLGA composites ranged from 18 to 38 MPa, while Young's modulus was in the range from 2 to 6 GPa.

삼차부틸알코올 기반 동결주조 공정을 이용한 PMMA 첨가 다공질 수산화아파타이트 지지체의 제조 및 특성 평가

김태림,윤석영,허진영,이치승,Kim, Tae-Rim,Yoon, Seog-Young,Heo, Jin-Young,Lee, Chi-Seung 한국결정성장학회 2017 한국결정성장학회지 Vol.27 No.5

기공 제어가 가능한 다공질 인공 지지체를 제조하기 위해 HA 분말에 기공형성제 역할을 하는 PMMA 분말을 첨가하여 TBA를 용매로 한 slurry를 합성한 후 동결주조와 소결을 거쳐 주상형 기공채널이 상호 연결되어 있는 다공질 HA 지지체를 제조하였다. PMMA 분말의 첨가량에 따른 HA 지지체의 결정구조는 XRD로 측정하였고 SEM을 통하여 지지체의 표면 및 내부 단면을 관찰하였는데, 소결과정에서 PMMA의 탈지가 지지체의 내부구조와 HA 분말의 결정성에 영향을 미치는 것으로 결과가 나타났다. 또한 지지체의 물리적 및 기계적 특성을 평가하여 기공형성제의 첨가량을 조절함으로써 기공률 및 기공 크기와 압축 강도의 제어가 가능하였다. 본 연구 결과, HA 지지체가 천연 해면골과 구조 및 특성이 유사하였으며 이를 통해 PMMA 첨가 다공질 HA 지지체가 조직공학용 인공 골지지체로서 자가골을 대체하여 사용이 가능한 것으로 판단된다. In order to prepare porous scaffolds capable of pore control, PMMA powder serving as a pore-forming agent was added to HA powder to synthesize a slurry containing TBA as a solvent. And then, porous HA scaffolds where pillarshaped pore channels interconnected with each other were fabricated by freeze-casting and sintering. The crystal structure of the HA scaffolds according to the addition amount of PMMA powder was measured by XRD and the surface and inner cross section of the scaffolds were analyzed through SEM. It was found that removal of PMMA during sintering affects the internal structure of the scaffolds and the crystallinity of the HA powder. Furthermore, through evaluating the physical and mechanical properties of the scaffolds, it was confirmed that the porosity, pore size and compressive strength can be controlled by controlling the addition amount of the pore-forming agent. It was also found that the HA scaffolds produced in this study were similar in structure and properties to the natural cancellous bone. This suggests that porous HA scaffolds with PMMA can be used as an alternative to autogenous bone for tissue engineering as an artificial bone scaffold.

동결주조 다공질 뮬라이트 세라믹스의 제조와 석탄회의 재활용

김규헌,윤석영,박홍채,Kim, Kyu Heon,Yoon, Seog Young,Park, Hong Chae 한국재료학회 2016 한국재료학회지 Vol.26 No.2

In order to fabricate porous mullite ceramics with controlled pore structure and improved mechanical strength, a freeze casting route has been processed using camphene mixed with tertiary-butyl alcohol (TBA) and coal fly ash/alumina as the solvent and the ceramic material, respectively. After sintering, the solidification characteristics of camphene and TBA solvent were evident in the pore morphology, i.e., dendritic and straight pore channels formed along the solidification directions of camphene and TBA ice, respectively, after sublimation. Also, the presence of microcracks was observed in the bodies sintered at $1500^{\circ}C$, mainly due to the difference in solidification volume change between camphene and TBA. The compressive strength of the sintered bodies was found generally to be dependent, in an inverse manner, on the porosity, which was mainly determined by the processing conditions. After sintering at $1300{\sim}1500^{\circ}C$ with 30~50 wt% solid loading, the resulting mullite ceramics showed porosity and compressive strength values in ranges of 83.8~43.1% and 3.7~206.8 MPa, respectively.

수성 알루미나/탄화규소 슬러리의 동결주조와 층상복합체의 제조

Tae Young Yang(양태영),Yong Ki Cho(조용기),Young Woo Kim(김영우),Seog Young Yoon(윤석영),Hong Chae Park(박홍채) 한국세라믹학회 2008 한국세라믹학회지 Vol.45 No.2

Symmetric three layer composites have been prepared by freeze casting and then pressureless sintered at 1700-1800℃ in N₂ gas atmosphere. The relative sintered density of multilayer composites having microstructural characteristics of later intermediate-stage densification increased with sintering temperature and reached about 95% theoretical value at 1800℃. Although the indentation strength of the multilayer composites was generally reduced with increasing Vickers indentation load up to 294N, the damage resistance of multilayer composites was superior compared to monolithic layer 95AL/5SN material. The three-point bend strength of the layered materials remained at the values 266-298 MPa after indentation with a load of 49N, while that of the monolithic 95AL/5SN material was 219MPa. The fracture toughness of the multilayer material was 5.4-6.6MPaㆍm1/2.

졸-겔법에 의한 Cobalt 치환된 Ba-ferrite 분말의 자기적 특성

최현승,박효열,윤석영,신학기,김태옥,Choi, Hyun-Seung,Park, Hyo-Yul,Yoon, Seog-Young,Shin, Hak-Gi,Kim, Tae-Ok 한국세라믹학회 2002 한국세라믹학회지 Vol.39 No.8

본 연구에서는 TMS[Tetramethylsilane:$Si(CH_3)_4$], $NH_3$와 $H2$를 이용하여 나노크기의 Si-C-N precursor 분말을 합성하기 위하여 CVC법을 이용하였으며 반응온도, TMS/$NH_3$ 비 그리고 TMS/$H_2$ 비를 변화시켰다. XRD와 FESEM 분석을 통해서 결정상과 입자의 크기 그리고 입자의 형태를 관찰하고자 하였으며, 그 결과 제조된 분말은 모든 실험 조건하에서 87∼130 nm 크기를 지닌 균일한 구형의 비정질 분말이 얻어졌다. 입자 크기는 반응온도의 감소에 따라 감소하였으며, 또한 TMS/$NH_3$, TMS/$H_2$ 비가 작아질수록 감소하였다. EA 분석 결과 제조된 분말은 Si, N, C, H로 이루어졌음을 알 수 있었으며 FT-IR를 통하여 Si-N, C-N, Si-C 결합을 가진 Si-C-N precursor 분말이 제조되었다. In this study, nano-sized Si-C-N precursor powders were synthesized by Chemical Vapor Condensation Method(CVC) using TMS(Tetramethylsilane: $Si(CH_3)_4$), $NH_3$ and $H_2$ gases under the various reaction conditions of the reaction temperature, TMS/$NH_3$ ratio and TMS/$H_2$ ratio. XRD and FESEM were used to analysis the crystalline phase and the average particle size of the synthesized powders. It was found that the obtained powders under the considering conditions were all spherical amorphous powder with the particle size of 87∼130 nm. The particle size was decreased as the reaction temperature increased and TMS/$NH_3$ and TMS/$H_2$ ratio decreased. As the results of EA analysis, it was found that the synthesized powders had been formed the powders composed of Si, N, C and H. Through FT-IR results, it was found that the synthesized powders were Si-C-N precursor powders with Si-C, Si-N and C-N bonds.

Ti-Al-Fe계 합금의 고온산화거동에 미치는 Fe의 영향

윤장원,현용택,김정한,염종택,윤석영,Yoon, Jang-Won,Hyun, Yong-Taek,Kim, Jeoung-Han,Yeom, Jong-Taek,Yoon, Seog-Young 한국재료학회 2011 한국재료학회지 Vol.21 No.7

In this paper, high temperature oxidation behavior of newly developed alloys, Ti-6Al-4Fe and Ti-6Al-1Fe, is examined. To understand the effect of Fe on the air oxidation behavior of the Ti-Al-Fe alloy system, thermal oxidation tests are carried out at $700^{\circ}C$ and $800^{\circ}C$ for 96 hours. Ti-6Al-4V alloy is also prepared and tested under the same conditions for comparison with the developed alloys. The oxidation resistance of the Ti-Al-Fe alloy system is superior to that of Ti-6Al-4V alloy. Ti-6Al-4V shows the worst oxidation resistance for all test conditions. This is not a result of the addition of Fe, but rather it is due to the elimination of V, which has deleterious effects on high temperature oxidation. The oxidation of the Ti-Al-Fe alloy system follows the parabolic rate law. At $700^{\circ}C$, Fe addition does not have a noticeable influence on the amount of weight gain of all specimens. However, at $800^{\circ}C$, Ti-6Al-4Fe alloy shows remarkable degradation compared to Ti-6Al-1Fe and Ti-6Al. It is discovered that the formation of $Al_2O_3$, a diffusion resistance layer, is remarkably hindered by a relative decrease of the ${\alpha}$ volume fraction. This is because Fe addition increases the volume fraction of ${\beta}$ phase within the Ti-6Al-xFe alloy system. Activities of Al, Ti, and Fe with respect to the formation of oxide layers are calculated and analyzed to explore the oxidation mechanism.

실란처리된 하이드록시프로필 메틸셀룰로오스/상전이된 칼슘포스페이트 복합체 골시멘트의 제조 및 특성평가

정나현,김동현,조훈상,윤석영,Jeong, Nahyun,Kim, Dong-Hyun,Cho, Hoon-Sang,Yoon, Seog-Young 한국결정성장학회 2016 한국결정성장학회지 Vol.26 No.6

Silanized-hydroxypropyl methylcellulose (Si-HPMC)/phase transformed calcium phosphate (PTCP) composites are prepared to purpose application of injectable bone cements with enhanced biocompatibility. The crystal structure and chemical state of the synthesized PTCP and Si-HPMC as solid and liquid phase of the composite cements were measured by XRD and FT-IR. The handling and mechanical properties of cements were measured by injectability tests and three-point bending tests. The in-vitro mechanical properties, XRD, and SEM results of bone cements were showed that enhanced hardening behavior was an inherent function of bone cements after in-vitro test. The cytotoxicity result of bone cements also was showed enhanced biocompatibility. Therefore, these injectable cements had potential be used as calcium phosphate cements for biomedical applications. 실란처리된 하이드록시프로필 메틸셀룰로오스/상전이된 칼슘포스페이트 복합체 시멘트는 향상된 생체적합성을 가지는 주입이 가능한 골시멘트로서 제조 되었다. 복합체 시멘트의 고체상과 액체상으로서 상전이된 칼슘포스페이트와 실란처리된 하이드록시프로필 메틸셀룰로오스의 결정구조 및 화학적 상태는 XRD 및 FT-IR에 의해 측정 되었고, 시멘트의 조작성 및 기계적 물성은 주입성 및 3점 굽힘 시험에 의해 측정하였다. 체외에서 진행된 골시멘트의 기계적 물성, XRD 및 SEM 결과는 골시멘트의 고유 기능으로서의 향상된 경화거동을 보였다. 또한 골시멘트의 세포독성 결과 향상된 생체적합성을 보였다. 따라서 이러한 주입이 가능한 시멘트는 생체의학 응용에 대한 칼슘포스페이트 시멘트로서 사용이 가능하리라 판단되어진다.

일축배향 기공채널과 향상된 압축강도를 갖는 다공질 알루미나/뮬라이트 층상 복합체

김규헌,김태림,김동현,윤석영,박홍채,Kim, Kyu Heon,Kim, Tae Rim,Kim, Dong Hyun,Yoon, Seog Young,Park, Hong Chae 한국세라믹학회 2014 한국세라믹학회지 Vol.51 No.1

Three-layer porous alumina-mullite composites with a symmetric gradient porosity are prepared using a controlled freeze/gel-casting method. In this work, tertiary-butyl alcohol (TBA) and coal fly ash with an appropriate addition of $Al_2O_3$ were used as the freezing vehicle and the starting material, respectively. When sintered at $1300-1500^{\circ}C$, unidirectional macro-pore channels aligned regularly along the growth direction of solid TBA were developed. Simultaneously, the pore channels were surrounded by less porous structured walls. A high degree of solid loading resulted in low porosity and a small pore size, leading to higher compressive strength. The sintered porous layered composite exhibited improved compressive strength with a slight decrease in its porosity. After sintering at $1500^{\circ}C$, the layered composite consisting of outer layers with a 50 wt% solid loading showed the highest compressive strength ($90.8{\pm}3.7MPa$) with porosity of approximately 26.4%.