http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
박기정(Ki-Jung Park),이철희(Cheol-Hee Lee),강동규(Dong Gyu Kang),정동수(Dongsoo Jung) 대한설비공학회 2010 설비공학 논문집 Vol.22 No.6
In this study, external condensation heat transfer coefficients(HTCs) of R134a and R1234yf are measured on a plain, low fin, and Turbo-C tubes at the saturated vapor temperature of 39℃ with the wall subcooling of 3~8℃. R1234yf is a new alternative refrigerant of low greenhouse warming potential for replacing R134a which is one of the greenhouse gases controlled by Kyoto protocol and is used extensively in mobile air-conditioners. Test results show that the external condensation HTCs of R1234yf are very similar to those of R134a for all three surfaces tested. For the application of condensation heat transfer correlations to the design of condensers charged with R1234yf, thorough property measurements are needed for R1234yf in the near future.
개방 수조형 연구용 원자로의 조사체 냉각 계통 개념 설계
박기정(Ki-Jung Park),정민규(Minkyu Jung),서경우(Kyoungwoo Seo),김성훈(Seong-Hoon Kim) 대한기계학회 2019 대한기계학회 논문집. Transactions of the KSME. C, 산업기술과 혁신 Vol.7 No.2
연구용 원자로는 핵분열 연쇄 반응으로 발생한 중성자를 기초 연구에서 산업 및 공학적 응용 연구까지의 광범위한 분야에 걸쳐 이용하는 원자로이다. 이 중성자를 이용하는 가장 중요한 분야 중 하나는 매우 다양하게 사용되는 동위 원소 생산 분야이다. 여러 동위 원소 중 Mo-99는 전 세계적으로 의학 진단 등의 의료 분야에서 많이 사용되고 있으며, 이에 대한 수요가 해마다 증가하고 있다. Mo-99 조사시 발생하는 열량은 핵연료에서 발생하는 열량과 비슷한 수준으로 안정적인 Mo-99 생산을 위해서는 충분한 냉각 시스템 설계가 동반되어야 한다. 특히 외부 반사체에서 Mo-99 타깃을 조사할 경우 Mo-99 냉각을 위한 별도의 냉각 계통이 설계되어야 한다. 외부 반사체 내에서의 냉각수 흐름 방향에 따라 냉각계통 설계가 크게 달라지게 되며, 각 유동 방향에 따른 장단점을 분석하여 계통 설계에 적용해야 한다. 본 연구에서는 Mo-99를 포함한 조사체 냉각 계통 설계에 적용 가능한 냉각 계통 개념을 제안하였으며, 이를 바탕으로 개방 수조형 연구용 원자로의 조사체 냉각 계통 개념 설계를 수행하였다. Research reactors are nuclear reactors that utilize fission chain reactions for a wide range of applications, from basic research to industrial and engineering applications. One of the most important application areas is the radioisotope production area. Mo-99 is widely used in medical fields such as medical diagnosis and the demand for Mo-99 is increasing every year. The heat generated by Mo-99 irradiation is similar to that from nuclear fuel, so sufficient cooling system design must be accompanied by stable Mo-99 production. In particular, when Mo-99 target is irradiated on an out-core reflector, an independent cooling system for Mo-99 should be designed. The design of the cooling system depends on the flow direction of the cooling water in the out-core reflector. The characteristic of each flow direction should be analyzed and applied to the conceptual design. In this study, the applicable conceptual design of irradiation targets cooling system of open pool research reactor was proposed.
평활관과 낮은 핀관에서 R245fa의 풀 비등 열전달계수
박기정(Ki-Jung Park),이요한(Yohan Lee),임병덕(Byeongdeok Lim),정동수(Dongsoo Jung) 대한설비공학회 2011 설비공학 논문집 Vol.23 No.3
In this work, pool boiling heat transfer coefficients(HTCs) of R22, R123, R134a, and R245fa are measured on both horizontal plain and 26 fpi low fin tubes. The pool boiling temperature is maintained at 7℃ and heat flux is varied from 80 ㎾/㎡ to 10 ㎾/㎡ with an interval of 10 ㎾/㎡. Wall temperatures are measured directly by thermocouples inserted through holes of 0.5 ㎜ diameter. Test results show that HTCs of high vapor pressure refrigerants are usually higher than those of low pressure fluids in both plain and low fin tubes. On a plain tube, HTCs of R245fa are 23.3% higher than those of R123 while on a 26 fpi low fin tube, HTCs of R245fa are 46.3% higher than those of R123. The fin effect is more prominent with low vapor pressure refrigerants than with high vapor pressure ones due to a sweeping effect.
부품영상인식을 통한 SPOT용접 자동화시스템의 설계 및 구현
박기정(Ki-Jung Park),송하주(Ha-Joo Song) 한국멀티미디어학회 2010 한국멀티미디어학회 학술발표논문집 Vol.2010 No.2
기존의 SPOT용접시스템은 작업자의 부주의로 인한 불량이 자주 발생한다. 이를 위해 비전카메라를 설치해서 용접되는 부품을 인식하고, 용접된 제품과 수량 등의 관리항목을 집중 관리하는 SPOT용접 자동화시스템을 제안한다. 제안하는 시스템은 공급기에서 공급한 너트나 볼트를 사람의 육안만으로 확인하여 용접하는 기존의 방식과는 달리, 비전카메라를 이용하여 부품의 유무와 뒤집힘 등을 확인한 후 용접하고, 수량카운터와 드레싱 등의 관리항목을 자동 관리한다. 따라서 용접 불량률을 감소시키고 작업 관리자의 업무 효율성을 높일 수 있다.
극저온 열처리 공정이 6061 알루미늄 합금의 잔류응력과 인장특성에 미치는 영향
박기정 ( Ki Jung Park ),고대훈 ( Dea Hoon Ko ),김병민 ( Byung Min Kim ),임학진 ( Hak Jin Lim ),이정민 ( Jung Min Lee ),조영래 ( Young Rae Cho ) 대한금속재료학회(구 대한금속학회) 2011 대한금속·재료학회지 Vol.49 No.1
To develop a 6061 aluminum alloy with low residual stress and high tensile strength, a cryogenic treatment process was investigated. Compared to the conventional heat treatment process for precipitation hardening with artificial aging, the cryogenic treatment process has two additional steps. The first step is cryogenic quenching of the sample into liquid nitrogen, the second step is up-hill quenching of the sample into boiling water. The residual stress for the sample was measured by the sin2 ψ method with X-ray diffraction. The 6061 aluminum alloy sample showed 67% relief in stress at the cryogenic treatment process with artificial aging at 175℃. From this study, it was found that the optimum cryogenic treatment process for a sample with low residual stress and high tensile strength is relatively low cooling speed in the cryogenic quenching step and a very high heating speed in the up-hill quenching step.