http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
나노 충진제 첨가량 변화에 따른 에폭시 복합재료의 체적고유저항 특성
김정식(Joung-Sik Kim),정인범(In-Bum Jeong),한현석(Hyun-Suk Han),이종용(Jong-Yong Lee),김귀열(Gwi-Yeol Kim),신종열(Jong-Yeol Sin),홍진웅(Jin-Woong Hong) 대한전기학회 2010 대한전기학회 학술대회 논문집 Vol.2010 No.7
최근 Nano 분야의 발전으로 전력변성기기 성형재료의 전기적 특성을 개질하기 위하여 몰딩 절연재료인 에폭시 수지에 나노 충진제의 첨가량 변화에 따른 체적 고유저항 특성에 미치는 영향을 연구하였다. 여러 가지 나노 물질 중 입자 크기가 50 [㎚]인 MgO를 초음파 믹서기를 사용하여 Epoxy 수지에서 분산이 잘 되도록 일정 시간동안 교반하여 시료를 제작 하였다. 제작된 시료는 MgO 첨가량 1.0 [wt%], 3.0 [wt%], 5.0 [wt%], 10.0 [wt%]와 MgO를 첨가하지 않은 순수 시료로 분류하여 실험을 하였다. 실험 결과 온도 변화에 따라 모든 시료는 80 [℃]이하 저온영역에서는 인가전압 증가에 따라 체적 고유저항도 일정하게 증가하는 것을 확인하였고, 측정온도 80 [℃]를 초과(고온영역)하면 Virgin시료와 나노 MgO를 첨가한 시료는 인가전압이 증가하여도 체적 고유저항은 일정함을 확인하였다. 특히, 측정범위에서 나노 충진제 3.0 [wt%] 일 때, 가장 우수한 체적 고유저항 2.6 × 10¹? [Ω · ㎝]을 얻었으며, 120 [℃]에서는 Virgin시료 보다 약 6.11배 증가함을 확인하였다.
공정가스와 RF 주파수에 따른 웨이퍼 표면 텍스쳐 처리 공정에서 저반사율에 관한 연구
윤명수,현덕환,진법종,최종용,김정식,강형동,이준신,권기청,Yun, Myoung-Soo,Hyun, Deoc-Hwan,Jin, Beop-Jong,Choi, Jong-Young,Kim, Joung-Sik,Kang, Hyoung-Dong,Yi, Jun-Sin,Kwon, Gi-Chung 한국진공학회 2010 Applied Science and Convergence Technology Vol.19 No.2
Conventional surface texturing in crystalline silicon solar cell have been use wet texturing by Alkali or Acid solution. But conventional wet texturing has the serious issue of wafer breakage by large consumption of wafer in wet solution and can not obtain the reflectance below 10% in multi crystalline silicon. Therefore it is focusing on RIE texturing, one method of dry etching. We developed large scale plasma RIE (Reactive Ion Etching) equipment which can accommodate 144 wafers (125 mm) in tray in order to provide surface texturing on the silicon wafer surface. Reflectance was controllable from 3% to 20% in crystalline silicon depending on the texture shape and height. We have achieved excellent reflectance below 4% on the weighted average (300~1,100 nm) in multi crystalline silicon using plasma texturing with gas mixture ratio such as $SF_6$, $Cl_2$, and $O_2$. The texture shape and height on the silicon wafer surface have an effect on gas chemistry, etching time, RF frequency, and so on. Excellent conversion efficiency of 16.1% is obtained in multi crystalline silicon by RIE process. In order to know the influence of RF frequency with 2 MHz and 13.56 MHz, texturing shape and conversion efficiency are compared and discussed mutually using RIE technology. 일반적으로 결정질 실리콘 태양전지에서 표면에 텍스쳐링(texturing)하는 것은 알칼리 또는 산성 같은 화학용액을 사용하고 있다. 그러나 실리콘 부족으로 실리콘의 양의 감소로 인하여 웨이퍼 두께가 감소하고 있는 추세에 일반적으로 사용하고 있는 습식 텍스쳐링 방법에서 화학용액에 의한 많은 양의 실리콘이 소모되고 있어 웨이퍼의 파손이 심각한 문제에 직면하고 있다. 그리하여 습식 텍스쳐링 방법보다는 플라즈마로 텍스쳐링할 수 있는 건식 텍스쳐링 방법인 RIE (reactive ion etching) 기법이 대두되고 있다. 그리고 습식 텍스쳐링으로는 결정질 실리콘 태양전지의 반사율을 10% 이하로는 낮출 수가 없다. 다결정 실리콘 웨이퍼 표면에 텍스쳐링을 하기 위하여 125 mm 웨이퍼 144개를 수용할 수 있는 대규모 플라즈마 RIE 장비를 개발하였다. 반사율을 4% 이하로 낮추기 위하여 공정가스는 $Cl_2$, $SF_6$, $O_2$를 기반으로 RIE 텍스쳐링을 하였고 텍스쳐링의 모양은 공정가스, 공정시간, RF 주파수 등에 의해 조절이 가능하였다. 본 연구에서 RIE 공정을 통하여 16.1%의 변환효율을 얻었으며, RF 주파수가 텍스쳐링의 모양에 미치는 영향을 살펴보았다.
광 입사각이 BIPV에 적용되는 단결정 또는 비정질 실리콘 태양전지의 양자효율에 미치는 영향
강정욱,손찬희,조광섭,유진혁,김정식,박창균,차성덕,권기청,Kang, Jeong-Wook,Son, Chan-Hee,Cho, Guang-Sup,Yoo, Jin-Hyuk,Kim, Joung-Sik,Park, Chang-Kyun,Cha, Sung-Duk,Kwon, Gi-Chung 한국진공학회 2012 Applied Science and Convergence Technology Vol.21 No.1
건재 일체형 태양광발전(BIPV) 응용을 위해 광 입사각에 따른 태양전지의 변환 효율은 중요하다. 양자효율은 태양전지의 파장별 전자 수집효율을 말하며, 입사각별 양자효율 측정으로 입사각에 따른 태양전지 출력 변화 요인을 분석할 수 있다. 이러한 입사각별 양자효율은 태양전지 종류에 따라 차이를 보인다. 본 연구에서는 가장 많이 쓰이는 벌크형 단결정 실리콘 태양전지와 박막형 비정질 실리콘 태양전지의 입사각별 양자효율을 비교하였다. 그 결과, 단결정 실리콘 태양전지에서는 광 입사각이 증가함에 따라 전 파장영역에서 양자효율이 감소했다. 반면, 비정질 박막 실리콘 태양전지에서는 단파장 영역에서는 결정질 실리콘과 동일하게 감소하였으나, 그 이후의 흡수 영역에서 약 $40^{\circ}$의 입사각까지 증가 또는 일정한 양자효율을 보이다가 이후에 급격히 감소하는 결과를 얻었다. 이는 비정질 박막 실리콘 태양전지에서 입사각이 증가함에 따라 특정 파장 영역에서 산란과 박막 구조의 영향으로 예상된다. 따라서, 태양전지의 구조 및 광학 구조 최적화 등으로 BIPV 적용에 유리한 구조 태양전지 제작이 가능할 것으로 보인다. The conversion efficiency of solar cells depending on incident angle of light is important for building-integrated photovoltaics (BIPV) applications. The quantum efficiency is the ratio of the number of charge carriers collected by the solar cell to the number of photons of a given energy shining on the solar cell. The analysis of angle dependence of quantum efficiencies give more information upon the variation of power output of a solar cell by the incident angle of light. The variations in power output of solar cells with increasing angle of incidence is different for the type of cell structures. In this study we present the results of the quantum efficiency measurement of single-crystalline silicon solar cells and a-Si:H thin-film solar cells with the angle of incidence of light. As a result, as the angle of incidence increases in single-crystalline silicon solar cells, quantum efficiency at all wavelength (300~1,100 nm) of light were reduced. But in case of a-Si:H thin-film solar cells, quantum efficiency was increased or maintained at the angle of incidence from 0 degree to about 40 degrees and dramatically decrease at more than 40 degrees in the range of visible light. This results of quantum efficiency with increasing incident angle were caused by haze and interference effects in thin-film structure. Thus, the structural optimization considering incident angle dependence of solar cells is expected to benefit BIPV.
TDMA 기반 MANET을 위한 계층교차적 네트워크 동기 아키텍처 연구
서명환(Myunghwan Seo),김정식(Joung-Sik Kim),조형원(Hyung-Weon Cho),정성헌(Sunghun Jung),박종호(Jongho Park),이태진(Tae-Jin Lee) 한국통신학회 2012 韓國通信學會論文誌 Vol.37 No.8B
MANET에서 TDMA MAC 프로토콜을 사용하기 위해서는 단말의 이동과 전파 환경의 영향으로 토폴로지가 계속적으로 변화하는 환경에서도 단말 간에 정밀한 동기를 유지할 수 있어야 한다. 본 논문에서는 TDMA 기반 MANET을 위한 in-band 방식의 계층교차적 네트워크 동기 구조를 제시한다. TDMA MAC 프로토콜과 proactive routing 프로토콜 간에 긴밀한 협력을 통해 단말 이동에 따른 네트워크 분리 및 통합을 신속하게 감지하고 네트워크 동기를 정밀하게 유지한다. 또한 제안된 동기 구조를 OPNET 시뮬레이터에 구현하고 다양한 시뮬레이션 시나리오를 통해 동기구조의 성능을 검증한다. 시뮬레이션 결과 네트워크 분리와 통합이 발생했을 때 이를 신속하게 인지하고 동기를 안정적으로 유지하는 것으로 나타났다. TDMA MAC protocol in MANET requires precise network synchronization between nodes though network topology changes continuously due to node mobility and the effect of propagation environment. In this paper we propose in-band cross-layer network synchronization architecture for TDMA-based MANETs. In the proposed architecture TDMA MAC protocol and proactive routing protocol cooperate closely to rapidly detect network partition and merge caused by node mobility and to precisely maintain network synchronization. We also implement the proposed synchronization architecture in OPNET simulator and evaluate the performance of it in various simulation scenarios. Simulation results show that our architecture stably maintains network time synchronization in both network partition and merge situations.
RIE 표면 텍스쳐링 모양에 따른 결정질 실리콘 태양전지의 영향
박인규,윤명수,현덕환,진법종,최종용,김정식,강형동,권기청,Park, In-Gyu,Yun, Myoung-Soo,Hyun, Deoc-Hwan,Jin, Beop-Jong,Choi, Jong-Yong,Kim, Joung-Sik,Kang, Hyoung-Dong,Kwon, Gi-Chung 한국진공학회 2010 Applied Science and Convergence Technology Vol.19 No.4
다결정 실리콘 웨이퍼 표면에 대면적 reactive ion etching (RIE) 장비로 표면 텍스쳐를 형성한 뒤 태양전지를 제작하였다. 웨이퍼 표면에 텍스쳐를 형성하는 것은 광학적 손실을 줄이기 위해 일반적으로 사용되는 방법으로 alkaline etching이 사용된다. 그러나 다결정 실리콘 태양전지의 경우 재료의 결정 방향에 따라 식각되는 alkaline etching은 텍스쳐링의 모양을 제어할 수 없어 효과적이지 못하다. 이와 달리 플라즈마 식각방법을 사용하면 표면 텍스쳐의 모양을 효과적으로 제어하여 조금 더 낮은 반사율을 얻을 수 있다. 하지만 텍스쳐 모양 조절로 얻은 낮은 반사율이 항상 높은 변환효율을 얻을 수 있는 것은 아니다. 본 연구에서는 대면적 RIE 공정 조건별로 얻은 태양전지 표면 텍스쳐의 모양에 따라 각각의 반사율과 양자효율 및 변환효율이 미치는 영향을 살펴보았다. We fabricated a plasma texturing for multi-crystalline silicon cells using reactive ion etching (RIE). Multi-crystalline Si cells have not benefited from the cost-effective wet-chemical texturing processes that reduce front surface reflectance on single-crystal wafers. Elimination of plasma damage has been achieved while keeping front reflectance to extremely low levels. We will discuss reflectance, quantum efficiency and conversion efficiency for multi-crystalline Si solar cell by each RIE process conditions.
노드 이동성 및 분포를 고려한 향상된 다중 점 릴레이 선택 알고리즘
박종호(Jongho Park),오창영(Chang-Yeong Oh),안지형(Ji Hyoung Ahn),김정식(Joung-Sik Kim),정성헌(Sunghun Jung),이태진(Tae-Jin Lee) 한국통신학회 2012 韓國通信學會論文誌 Vol.37 No.12B
본 논문에서는 노드의 이동성이 크고 노드의 밀도가 균일 하지 않은 애드혹 네트워크에서 라우팅 성능을 개선하기 위해 노드의 이동성과 밀도를 고려하여 OLSR(Optimized Link State Routing) 의 MPR(Multi-Point Relay) 선택방법을 개선할 수 있는 방법을 제안한다. OLSR의 MPR 선택 방법은 노드의 이동성과 밀도에 무관하게 2홉 이웃 노드를 많이 포함하는 노드를 위주로 선택한다. 하지만 노드가 이동성을 갖는 경우에 이동성이 큰 노드를 MPR로 선택할 경우 성능이 저하될 수 있다. 또한 노드의 밀도가 균일 하지 않은 경우에는 밀도가 높은 지역의 노드들이 우선적으로 MPR로 선택되면 네트워크 전체의 성능을 향상시킬 수 있다. 따라서 본 논문에서는 노드의 이동성과 밀도를 Hello 메시지 교환을 통해 측정하고 노드의 이동성과 밀도를 반영하여 MPR 선택에 우선순위를 부여하는 방법을 제안한다. 본 논문에서 제안한 MPR 선택 방법의 성능을 알아보기 위해 OPNET을 활용하여 시뮬레이션을 수행하고 제안 방법의 성능이 가장 우수함을 보인다. In this paper, we propose an improved MPR selection method considering mobility and density of nodes for ad-hoc networks. In Optimized Link State Routing(OLSR), a node selects 1-hop Multi-Point Relay(MPR) nodes to cover all 2-hop neighbor nodes. In a high population area, many nodes are likely to be selected as MPR nodes by their neighbors. This leads to increase in contention among MPR nodes and may decrease overall performance of the network. In addition, when an MPR node leaves the communication range of its MPR selector node, it can no longer perform as the MPR node and the performance of the network may also decrease. In this paper, we propose an MPR selection method which measures the mobility and density of nodes by exchanging the hello messages and gives the priorities to the nodes for MPR selection. Performance evaluation results using OPNET show that the proposed method is superior to OLSR or the MPR candidate method in terms of connectivity and throughput.