http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
유성근,우라시마가즈히로,Yu, Seong-Geun 한국재료학회 1996 한국재료학회지 Vol.6 No.9
본 연구는 가스압소결 질화규소의 혼합모드에 있어서 파괴거동을 실온 및 100$0^{\circ}C$에서 조사하였다. 실험은 누프압흔을 도입한 시험편을 사용하여 소둔처리에 의해 잔류응력을 제거하고, 4점굽힘법을 이용하였다. 실험결과, 종래 제창되고 있는 파괴기준과 일치하지 않고, 그래서 새롭게 4차관수의 근사식을 제안하였다.
유성근,Yu, Seong-Geun 한국재료학회 1997 한국재료학회지 Vol.7 No.3
2종류의 질화규소에 대하여 Ring형시험편을 이용하여 접촉피로시험을 하였다. 질화규소는 금속재료에서와 같은 형태의 피로현상을 나타냈고, 파면해석 및 관찰결과 접촉피로에 있어서 균열의 발생은 고탄소크롬강의 경우와 같이 표면하의 반복전단응력에 의한 것으로 밝혀졌다. 그리고 시험펴 파단면에서 표면하의 Heltz전단응력의 변동이 최대로 되는 깊이의 위치에 다수의 균열이 관찰되었다. Rolling contact fatigue tests were performed for two types silicon nitrides using disk- type specimens. Materials showed a fatigue behaviour similar to that typically found in metallic materials From the fractographic and metallographic observations, it has been found that the crack initation in the silicon nitrides subjected to rolling contact fatigue is to be induced by cyclic subsurface shear stress, as is known in steel bearing. On the mid-sections of the specimens, many subsurface cracks which lay parallel to the contact surface can be found at a depth where fluctuation of the Herzian shear stress was the maximum.
유성근,Yu, Seong-Geun 한국재료학회 1997 한국재료학회지 Vol.7 No.1
In the first part of the paper, the crack growth process in rolling contact fatigue has been investigated on ring type plate specimens, in which crack growth is two dimensional and cracks are observed on the side surface of the specimens. The results have shown that cracks are initated from the contact surface in tensile mode in the direction approximately normal to the contact surface and after some short length of growth, shear mode growth occurs from the tip of the crack and it grows until the separation of the surface layer, namely flakung type failure, occurs. In the second part, mode U fatigue crack growth tests have been made by using an apparatus designed based on the concept that the subsurface fatigue crack growth in rolling contact fatigue is the mode U fatigue crack growth under the stress state where the tensile mode growth is suppressed by compression stress. The rest results have shown that the mode U fatigue crack growth occurs if the superposed compression stress is enough to suppress the tensile mode growth. 본 연구에서는 접초피로에 있어서 균열의 발생, 진전 등의 관찰을 위해, 균열의 발생, 진전 등이 2차원적으로 되어 시험편측면에서 관찰이 가능한 평판 ring형 시험편을 이용하여 반복수 증대에 따른 균열의 발생, 진전과정을 조사하였다. 그 결과 pitting, flaking형 파손의 초기손상은 접촉면하의 내부에 생기는 접촉면에 평행방향의 균열에 의해 일어나며, 이 균열은 그 방향 밀 파면형태에 의해 접촉응력이 접촉면에 평행방향의 전단응력성분에 의한 모드 ll 피로진전과의 차는 중첩부하된 압축응력의 유무라고 생각되며, 이 가저에 근거로 하여 재료고유의 모드 ll 피로균열진전특성을 구할 수 있는 장치를 개발하였다. 이 장치를 이용하여 알루미륨합금 및 공구강에 대한 da/dN-${\Delta}k$ ll 관계의 시험결과를 얻었다.
AR모델과 MLP를 이용한 단기 물 수요 예측 알고리즘 개발
최기선(Gee-Seon Choi),유철(Chool Yu),진력민(Ryuk-Min Jin),유성근(Seong-Keun Yu),전명근(Myung-Geun Chun) 한국지능시스템학회 2009 한국지능시스템학회논문지 Vol.19 No.5
본 논문은 비선형 특성을 내재한 물 수요예측을 위하여 기존의 시계열 자기회귀 알고리즘과 다층신경망 학습방법을 결합한 단기 물 수요 예측 알고리즘을 개발하였다. 제시된 방법을 검증하기 위한 사례연구로 2007년도와 2008년도 전북지역의 광역상수도 A정수장에서 취득된 데이터를 활용하여 알고리즘 구축 및 제안 방법의 정확도를 분석하였다. 실험 결과 다중 회귀모델은 MAPE가 5.1%, AR모델은 3.8%, 제안된 방법인 AR+MLP 모델은 3.6%로 나타나 성능이 우수한 것으로 나타났다. 따라서 제안된 방법을 사용할 경우 정수장에서 단기 물 수요예측에 유용하게 활용할 수 있음을 보였다. In this paper, we develope a water demand forecasting algorithm using AR(Auto-regressive) and MLP(Multi-layer perceptron). To show effectiveness of the proposed method, we analyzed characteristics of time-series data collected in "A" purification plant at Jeon-Buk province during 2007-2008, and then performed the proposed method with various input factors selected through various analyses. As noted in experimental results, the performance of three types model such as multi-regressive, AR(Auto-regressive), and AR+MLP(Auto-regressive + Multi-layer perceptron) show 5.1%, 3.8%, and 3.6% with respect to MAPE(Mean Absolute Percentage Error), respectively. Thus, it is noted that the proposed method can be used to predict short-term water demand for the efficient operation of a water purification plant.
정재호 ( Jeong Jae Ho ),윤순종 ( Yun Sun Jong ),유성근 ( Yu Seong Geun ) 한국복합재료학회 2003 Composites research Vol.16 No.5
본 연구는 면내 선형분포하중이 작용하는 직교이방성판의 좌굴거동에 관한 것으로서, 하중이 재하된 두 변은 단순지지되어 있으며 하중이 재하되지 않은 두 변은 회전에 대해 탄성구속된 경계조건을 포함하여 다양한 경계조건을 갖는 직교이방성판의 좌굴해석식을 정밀해법을 사용하여 유도하였다. 좌굴해석 수행 결과를 사용하여 하중이 재하되지 않은 두 변이 특정 경계조건인 경우를 포함하여 회전에 대해 탄성구속된 판의 좌굴해석을 위한 근사식을 판의 형상비와 탄성구속 정도를 나타내는 계수 및 재료의 성질의 함수로 제시하였다. 제시된 근사식을 사용할 경우 재료의 성질과 판의 형상비 및 하중이 재하되지 않은 변의 탄성구속정도를 알면 단순계산으로 직교이방성판의 좌굴해석을 수행할 수 있도록 하였다. 여러 가지 직교이방성 재료에 대해 근사식에 의한 해석결과와 정밀해법에 의한 해석결과를 비교한 결과 1.5% 미만의 차를 나타냈었다. In this study, the analytical investigation of orthotropic rectangular plate is presented. The loaded edges are assumed to be simply supported and the unloaded edges could have elastically restrained boundary conditions including the extreme boundary condition such as simple, fixed, and free. Using the closed-form solutions, the buckling analyses of orthotropic plate with arbitrary boundary conditions are performed. Based on the data obtained by conducting numerical analysis, the simplified form of equation for finding the buckling coefficient of plate with elastically restrained boundary conditions at the unloaded edges is suggested as a function of aspect ratio, elastic restraint, and material properties of the plate. The results of buckling analyses by closed-form solution and simplified form of solution are compared for various orthotropic material properties. It is confirmed that the difference of results is less than 1.5%.