사토(砂土)를 이용(利用)한 급속토양삼투법(急速土壤?透法)의 폐수처리(廢水處理) 특성(特性)에 관한 연구(?究)

양상현,조웅현,Yang, Sang Hyon,Cho, Woong Hyun 대한토목학회 1987 대한토목학회논문집 Vol.7 No.3

유기물(有機物)을 제거(除去)키 위한 토양처리(土壤處理) system에 있어서 특히 급속토양삼투법(急速土壤渗透法)은 다른 토양처리방법(土壤處理方法)에 비(比)해 기온(氣溫) 변화(變化)에 대한 제한(制限)을 덜 받고 수지면적(數地面積)을 적게 요구(要求)하는 것으로 알려져 있다. 따라서 급속토양처리(急速土壤處理)에 대한 본(本) 연구(硏究)에서는 유기물(有機物) 제거율(除去率)과 침투율(浸透率), 생물학적(生物學的) 산소흡수(酸素吸收)에 따른 용존산소(溶存酸素)의 변화(變化), 그리고 pH 등을 사토(砂土)를 채운 실험통(實驗筒)을 이용(利用)하여 규명코자 했으며 또한 단위면적당(單位面積當) COD 제거량(除去量) 및 TKN으로부터의 질산화율(窒酸化率) 등을 구(求)하였다. 그 결과(結果)는 다음과 같다. 1) 사시(砂尸)이 1m 이상(以上)인 경우 침투율(浸透率)이 15~20cm/day 이하(以下)에서는 COD제거(除去)가 90% 이상(以上)으로 안정(安定)하게 유지되며 지하수위(地下水位)까지의 깊이를 고려(考慮)하면 침투오염물(浸透汚染物)로 인(因)한 오염(汚染)영향은 매우 작다고 본다. 2) 단위면적당(單位面積當) COD 제거량(除去量)은 적절(適切)한 운영하(運營下)에서 10~14g/day를 쉽게 기대할 수 있고 기질분해(基質分解)는 대부분(大部分) media표층(表層)에서 이루어지는 것으로 판단된다. 3) 일반적(一般的)으로 TKN의 $NO_3{^-}$-N으로의 전환(轉換)은 상당한 체류시간(滯留時間)이 주어진다면 COD제거율(除去率)에 비례(比例)한다고 본다. In land treatment systems for organic waste removal, especially rapid intiltration method is well known as less climatic restrictions and less field area requirements as against the others. Therefore the present study on rapid infiltration is aimed to survey the waste removal rate, infiltration rate, variation of dissolved oxygen due to biological oxygen absorption and pH decrement using pilot infiltration column filled with permeable soil(sand) as media, also to find the waste load(COD) per unit area and nitrate conversion ratio from TKN. The results obtained here are as follows. 1) When the depth of sand layer is more than 1 meter, the COD removal would be reached steadly to 90% or more under the infiltration rate below 15~20cm/day, and would be no problem due to leached organic pollutants considering the depth of ground water table. 2) The COD removal per unit area($m^2$) can readily be expected to 10~14g/day with proper operation, and the decomposition of substrate would be attained mostly at the surface layer of the media. 3) Generally the conversion of TKN to the $NO_3{^-}$-N is seemed to be proportional to the COD removal rate if provided proper retention time.

구순구개열 환자에서 Locator^® 유지장치가 장착된 milled titanium bar를 이용한 가철성 임플란트 피개 국소의치의 보철수복증례

양상현,김경아,김자영,서재민,Yang, Sang-Hyun,Kim, Kyoung-A,Kim, Ja-Yeong,Seo, Jae-Min 대한치과보철학회 2015 대한치과보철학회지 Vol.53 No.3

본 증례는 구순구개열 환자에서 상순의 반흔, 상악 잔존치조제의 과도한 흡수, 협소한 구개 및 상악골의 열성장을 동반한 3급 악간관계로 인해 통상의 가철성 국소의치 수복에 한계를 보이기 때문에 상악 무치악 부위에 4개의 임플란트를 식립 후, CAD/CAM 시스템으로 밀링한 titanium bar를 이용한 상악 가철성 임플란트 피개 국소의치를 계획하였다. 통상의 주조방법은 주조 후 수축을 하게 되지만 CAD/CAM 시스템으로 밀링한 titanium bar는 높은 정밀성과 경제성 그리고 가벼운 장점이 있다. 하지만 실제 임상에서 milled bar는 아주 균등하고 정확한 마찰결합을 얻기 힘들며 의치의 반복적인 착탈에 의해 마찰 유지력이 감소 할 수 있다. 이에 milled bar와 함께 사용할 수 있는 다양한 보조 유지장치(e.g. friction pin, $ERA^{(R)}$, $CEKA^{(R)}$, magnetics, $Locator^{(R)}$ 등)를 같이 사용함으로써 부가적인 유지력, 경제성 및 교체의 용이성 등을 추가적으로 얻을 수 있다. 본 증례에서 milled titanium bar의 상부면에 drill and tapping 방법으로 $Locator^{(R)}$ 유지장치를 연결하였다. milled bar에 screw hole을 형성하고 3개의 $Locator^{(R)}$ 유지장치를 20 Ncm으로 체결하여 추가적인 유지력을 확보하였다. 보철수복 후, 환자가 원하는 심미적인 안모, 저작 기능 및 의치 유지에 만족할 만한 결과를 얻었기에 이를 보고하고자 한다. Due to the limitations of conventional removable partial denture prostheses to treat a cleft lip & palate patient who shows scar tissue on upper lip, excessive absorption of the maxillary residual alveolar ridge, and class III malocclusion with narrow palate and undergrowth of the maxilla, 4 implants were placed on the maxillary edentulous region and a maxillary removable implant-supported partial denture was planned using a CAD/CAM milled titanium bar. Unlike metal or gold casting technique which has shrinkage after the molding, CAD/CAM milled titanium bar is highly-precise, economical and lightweight. In practice, however, it is very hard to obtain accurate friction-fit from the milled bar and reduction in retention can occur due to repetitive insertion and removal of the denture. Various auxiliary retention systems (e.g. $ERA^{(R)}$, $CEKA^{(R)}$, magnetics, $Locator^{(R)}$ attachment), in order to deal with these problems, can be used to obtain additional retention, cost-effectiveness and ease of replacement. Out of diverse auxiliary attachments, $Locator^{(R)}$ has characteristics that are dual retentive, minimal in vertical height and convenient of attachment replacement. Drill and tapping method is simple and the replacement of the metal female part of $Locator^{(R)}$ attachment is convenient. In this case, the $Locator^{(R)}$ attachment is connected to the milled titanium bar fabricated by CAD/CAM, using the drill and tapping technique. Afterward, screw holes were formed and 3 $Locator^{(R)}$ attachments were secured with 20 Ncm holding force for additional retention. Following this procedure, satisfactory results were obtained in terms of aesthetic facial form, masticatory function and denture retention, and I hereby report this case.

Media를 충전(充塡)한 간접폭기식(間接曝氣式) 침지여상(浸漬濾床)에 의한 BOD제거 특성에 관한 연구

양상현,권영호,Yang, Sang Hyun,Kwon, Young Ho 대한토목학회 1994 대한토목학회논문집 Vol.14 No.3

침지여상에 폐수를 부하하여 간접포기 강제순환 방식으로 처리하는 system에 대하여 그 유기물 제거 특성을 실험적으로 연구했다. 실험은 침지여상에 네트링(random형(型) plastic media), 입체철망(module형(型) plastic media) 및 잔자갈의 특성이 다른 세가지 media를 충전하고, pH, 수온(水溫)을 고정한 상태에서 $BOD_5$ 용적부하와 순화비를 변동하여 실시하므로서 여재(media) 종류가 $BOD_5$ 제거효율에 미치는 특성을 규명했다. The BOD removal characteristics of submerged biofilters filled with three kinds of filter media respectively were experimentally examined with constant temperature, pH value and variable BOD loading and recirculation ratio. Obtained results are as follows; 1. The BOD removal ratio decreases with the increasing $BOD_5$ volumetric loading rate, and the loading rate for the BOD removal over 90% is lower thean $1.6kg{\cdot}BOD_5/m^3{\cdot}d$ for the plastic media of Netring and cubic wire meshes. This is a much large value than $0.3{\sim}0.8kg{\cdot}BOD_5/m^3{\cdot}d$ for conventional activated sludge process. The required submerged biofilter volume is found to be much samller than that of conventional activated sludge process. 2. The decreasing order of BOD removal is Netring (random plastic media), cubic wire meshes (plastic module), and then gravel (stone media). This is mainly due to the media characteristics such as void ratio, specific surface area and media shapes. 3. The $BOD_5$ removal rate increases with the recircuration ration, but the rate of increases becomes samaller as the recirculation ratio increases over 20. When $BOD_5$ loading is $1.8kg{\cdot}BOD_5/m^3{\cdot}d$, the required recirculation rationto obtain 90% $BOD_5$ removal is about 20 for Netring and it was about 30 for cubic wire meshes. 4. Reynold's Number increases with recirculation ratio, and the Reynold's Numbers corresponding to the recircuration ratio of 10~50 are less than 52, showing laminar up flows in the filter. The settled and effluent sludges increase with increase of Reynol's Number, and there are the definite Reynold's Numbers at which the settling sludge concentrations become nearly constant respectively in each filters. 5. In this submerged biofilter system, small volume of sludge hopper can be substituted for a separated settling tank.

불국토(佛國土) 사상에 따른 다불전(多佛殿) 사찰의 조영(造營) 개념 연구 - 불국사, 법주사, 부석사의 불전 배치를 중심으로 -

양상현,Yang, Sang-Hyun 한국건축역사학회 2005 건축역사연구 Vol.14 No.2

Temple with Multi-Buddha's Pavilions is a temple consisting of more than 2 Buddha's Pavilions. Individual Buddha's Pavilions tend to form distinguished area, or to keep independent axis from other Buddha's Pavilions. This study is to understand the philosophy of layout of individual Buddha's Pavilions located in the Temple with Multi-Buddha's Pavilions. To investigate a relationship to layout of individual Buddha's Pavilions on the basis of Buddhism doctrine makes us to understand philosophies about temple layout which temple constructors had. Bulkooksa, a temple having several pavilions placed in parallel, integrates diverse philosophies such as Vairocana Buddha-Ksetra from Vairocana Buddha's Pavilion, Sakyamuni Buddha-Ksetra from both Sakyamuni Buddha's Pavilion and two stupa, and Amitayus Buddha-Ksetra (Sukhavati) from Amitayus Buddha-Ksetra Pavilion. Sakyamuni Buddha's Pavilion and Amitayus Buddha's Pavilion are placed east to west in parallel, and Vairocana Buddha's Pavilion is placed behind them. Beobjusa, a temple having several pavilions placed cross axis, combines three axes such as the first, main axis linking Kumkang Gate - Chunwang Gate - Palsang Pavilion - Amitayus Buddha's Pavilion - Sakyamuni Buddha's Pavilion, the second axis linking Palsang Pavilion -Maitreya Pavilion, and the third axis linking Amitayus Buddha's Pavilion - Avalokiteshvara Pavilion. Relationship among each Buddha's land is clearly expressed by means of this cross axis layout of Buddha's Pavilions, reflecting a philosophy of rebirth in Nirvana that Wonhyo and Eusang propagated. Buseoksa, a temple having several pavilions placed the before and the behind, combines three Buddha's lands such as Maitreya Buddha-Ksetra, Amitayus Buddha-Ksetra and Vairocana Buddha-Ksetra, by means of arrangement of Maitreya Pavilion, Anyang Pavilion and Amitayus Buddha's Pavilion at bended axis, and east facing Amitayus Buddha. By investigating the philosophy of Temple layout with Multi-Buddha's Pavilions in this study, Buddha's Land conception, for people, that ancient Korean temples have, is understood.

가압부상법(加壓浮上法)에 의한 활성(活性)슬러지 혼합액(混合液)의 고액분리(固液分離)에 관한 연구(?究)

양상현,라덕관,Yang, Sang Hyun,Ra, Deog Gwan 대한토목학회 1985 대한토목학회논문집 Vol.5 No.3

An effective technique of sludge separation is required for concentrated activated sludge process. The dissolved-air flotation (DAF) has been shown to be efficient process for sludge separation. The factors affecting DAF process for activated sludge separation are type and concentration of sludge, air/solid ratio, ratio of pressurized water flow, pressure, sludge detention time, temperature, sludge and hydraulic loading rate, recycle flow rate of sludge and type and quantity of chemical aid. In order to study the optimal operation condition for sludge separation, the influence factors such as type and concentration of sludge, ratio of pressurized water flow and pressure are investigated by the batch and continuous reactor experiments of DAF and sedimentation test. By the experimental investigation, the results are as follows; 1. For the bulking and concentrated sludge, DAF is more effective than sedimentation for the sludge separation. 2. In DAF, the critical ratio of pressurized water flow exist. The critical value varies with the pressure in the tank. That is, according to the pressure changes from 3 to $5kg/cm^2$, the critical value varies from 0.25 to 0.67 accordingly. 3. Pressure affects the ratio of pressurized water flow, but it does not show any influence upon the DAF efficiency directly. 4. Continuous experimental results was not better than those of batch. 활성(活性)슬러지가 팽화(膨化)를 하였거나 환기조내(環氣槽內)의 MLSS 농도(濃度)가 높은 경우, 종래(從來)의 중력침전법(重力沈澱法)으로는 슬러지의 분리(分離)가 어렵다. 이 문제(問題)의 해결책으로 가압부상법(加壓浮上法)을 이용(利用)하는 방법(方法) 연구(硏究)하였다. 가압부상법(加壓浮上法)의 효과(效果)에 영향(影響) 주는 인자중(因子中) 중요(重要)하다고 생각되는 환기조내(環氣槽內)의 MLSS 온도(溫度), 슬러지의 성상( 性狀), 가압수량비(加壓水量比), 압력(壓力)의 변화(變化)에 따른 가압부상법(加壓浮上法)의 효율(效率)에 관하여 회분식(回分式) 실험(實險)과 연속식(連續式) 실허(實驗)을 실시하여 다음과 같은 결과(結果)를 얻었다. 활성(活性)슬러지가 혼합액(混合液)의 분리(分離)가 종래(從來)의 중력침전법(重力沈澱法)으로는 어려운 경우에도 가압부상법(加壓浮上法)은 매우 좋은 효과(效果)를 나타낸다. 가압부상법(加壓浮上法)에는 한계(限界) 가압수량비(加壓水量比)가 존재(存在)하며 이 한계치(限界値)는 압력(壓力)에 따라 변화(變化)한다. 압력(壓力)은 단지 가압수량비(加壓水量比)에만 영향(影響)을 미치고 그 외(外)의 가압부상(加壓浮上) 효율(效率)에는 거의 영향(影響)이 없다. 연속식(連續式) 실험(實驗)이 회분식(回分式) 실험(實驗)보다 다소 효율(效率)이 떨어진다.

대한제국의 군제 개편과 군사 예산 운영

양상현(Yang Sang-Hyun) 부산경남사학회 2006 역사와 경계 Vol.61 No.-

The military budget of the Great Han Empire occupied 25% of total amount of a national budget, and it reached up to 40% after 1901. The Great Han Empire expended central and local army organization with that budget. Reason of doing it, Empire could combine central army organization together, that managed in both Japanese and Russian style. First of all, local army organization, using temporary budget to repress the righteous army, unified to the Army for Suppression and Protection(鎭衛隊) with expansion of quantity in 1900. This should mean the local arms budget exceeded the central arms budget at that time. To consolidate military strengths, the Great Han Empire brought in military goods such as guns and bullets, and even tried to produce new weapons. In addition, in 1898 empire established military school, and educated initial officers with subjectivity not by foreigners but Korean instructors. However, modernization of military started to actualized after installation of the Marshal Headquarters(元帥府), which emperor could control army. This kind of tendency reflected directly to budget, so after the Marshal Headquarters(元帥府) established in 1899, the budget of the Marshal Headquarters(元帥府) kept surpassed the budget of Military Headquarters. Due to completion of reorganization in a military system of Great Han Empire, incompleteness in organizing arms budget solved, and they were able to operate military budget with stabilization. Furthermore, support of the Office of Crown Properties (內藏院) contributed to supplementation of difficulties in managing budgets with army circles. Nevertheless all of these successful results, trained soldiers usually used in saving palace, or keeping public security not defending country which is an actual reason why they were existed. As a result, even using enormous budget in expending army, they could not even deal with encroachment of Japan that progressed since 1904.

송광사(松廣寺) 가람 배치의 교리적 이해; 선교합일(禪敎合一) 사상과 그 건축적 실현

양상현 ( Sang Hyun Yang ) 한국기초조형학회 2010 기초조형학연구 Vol.11 No.5

사찰 佛殿 莊嚴의 상징 연구

양상현(Yang, Sang-hyun) 한국역사민속학회 2004 역사민속학 Vol.- No.19

『울산안핵록』을 통해서 본 1875년 울산농민항쟁

양상현 ( Sang Hyun Yang ) 한국고문서학회 2009 古文書硏究 Vol.35 No.-

大韓帝國期 내장원의 海稅 관리

楊尙弦(Yang, Sang Hyun) 울산대학교 사학회 1999 울산사학 Vol.8 No.-