http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
권정락 한국세라믹학회 1995 한국세라믹학회지 Vol.32 No.8
In order to investigate the performance of compression-type accelerometer on piezoelectric properties, PZT materials have been studied. The ring-shaped piezoelectric elements were prepared using commercial PZT powders by conventional ceramic process. Their estimated relative dielectric constant, piezoelectric charge constant (d33) and voltage constant (g33) values showed 390∼3400, (90∼593)×10-12 C/N and (19.5∼40.5)×10-3 V-m/N, respectively. The charge sensitivity of accelerometer is proportional to the piezoelectric charge constant value (d33) of PZT, but its voltage sensitivity is related with the piezoelectric voltage constant (g33). Since the mounted resonance frequency and sensitivity are dependent on the seismic mass as well as physical charateristics and size of PZT elements, the suitable considerations between two components are required for accelerometer's design.
신병철,권정락 ( Byoung Chul Shin,Jeong Rock Kwon ) 한국센서학회 1996 센서학회지 Vol.5 No.3
Steel wires are made by elongating hot billets. If the billets have internal or surface defects, the wire can be broken during elongation process. After testing surface defect, we are testing internal defect by ultrasonic transducers. POSCO is producing two kinds of billets, hot rolled billet and cast billet. Hot rolled one is denser than cast billet. Because of the low density and rough surface, ultrasonic testing is difficult for the cast billet. Size of the transducer was related with the size and density of the billet. A transducer having 21mm long, 8.5mm wide and 0.95mm thick piezoelectric ceramic plate was best for 160mm x 160mm cast billet. Center frequency of the transducer was 2.25MHz and the focus distance was 70mm.
폴리에틸렌 배관 전기융착부 단기성능 평가를 위한 융합물량 영향 평가
길성희,권정락,조지환,Kil, Seong-Hee,Kwon, Jeong-Rock,Jo, Ji-Hwan 한국에너지학회 2005 에너지공학 Vol.14 No.2
본 연구에서는 폴리에틸렌 배관 전기융착부 단기성능 평가를 위한 비파괴검사를 실시할 경우 발견되는 결함에 대한 판정기준을 개발하였다. 인위적으로 $3.8mm\~25mm$ 내에서 6가지 크기의 결함을 삽입한 시험 편을 설계 및 제작하여 기계적 평가를 실시하고 또 이론적 해석을 하였다. 안전계수 2를 적용하여 유효 응력을 산정할 경우 최대 허용 가능한 결함 크기는 11 mm(열선 폭의 $30\%$)이며 안전 계수를 4를 적용할 경우에 최대 허용 가능한 결함 크기는 3.8mm(열선 폭의 $10\%$)이다. In order to investigate the short-term performance of polyethylene electrofusion joints, the mechanical tests and stress analysis have been conducted to the artificially defected weld joints. The defects of lack of fusion with a square-type were fabricated with 10, 20, 30, 40, 50, 60$\%$ size of the width of heat-ing wire zone, respectively. In this defect sires range, both tensile and bending test results showed the dependence of defect size to the electrofusion joints performance, but both sustained pressure and crush test results didn't. The numerical stress analysis results including the soil and internal pressures, tensile and bend-ing stresses clearly showed the dependence of fusion defect size. Based on both mechanical test and stress analysis results, the maximum acceptable defect size in polyethylene electrofusion joints is discussed.