http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
택지조성공사 BIM을 위한 비탈면 3차원 모델링 효율화 방안에 관한 연구
권용규,하다현,김정환,서종원,심호,Kwon, Yongkyu,Ha, Dahyun,Kim, Jeonghwan,Seo, Joonwon,Shim, Ho 한국건설관리학회 2021 한국건설관리학회 논문집 Vol.22 No.4
최근 국내외에서 BIM (Building Information Modeling)에 대한 관심이 증가하며 도입사례가 증가하고 있으며, 3차원 모델링은 BIM의 도입을 위한 첫 단추다. 그러나 도로, 철도와 교량과 같은 토목시설물 중심의 3차원 모델링의 효율화 방안에 대한 연구는 많이 이루어지고 있는 반면, 토공사에는 3차원 모델링의 효율화 방안에 대한 연구가 부족한 실정이다. 특히 비탈면 설계는 주위 환경과 지반의 특성에 따라 복잡다단한 형상을 가지는 경우가 많기 때문에 사용자가 비탈면 3차원 모델을 작성하기 위해 효율적인 방안이 필요한 상황이다. 이에 본 연구에서는 국내에서 개발된 e-BIM 모델러와 해외 Autodesk 사의 Civil 3D의 비탈면 모델링 기능의 인터페이스와 절차를 세세히 분석하여 3차원 면의 생성 간격을 입력하는 기능, 기준지형을 다수로 선택하고 각 기준지형 별로 모델링 파라미터를 입력하고 저장할 수 있는 기능을 개발하고 인터페이스를 개선하였다. 본 연구에서 개발한 시스템은 앞서 분석한 소프트웨어와 비교하였을 때 5단계의 절차만으로 효율적으로 비탈면 3차원 모델링을 수행할 수 있고, 클릭 및 입력횟수를 줄일 수 있었다. 본 시스템의 검증을 위해서 개발한 시스템과 타 소프트웨어를 활용하여 동일한 조건 및 형상의 비탈면 모델링을 수행한 결과, 개발한 시스템을 통해 비탈면 모델링을 3회 실시하면 타 소프트웨어를 사용할 때보다 숙련자의 경우 최소 1.8배, 비숙련자의 경우 최소 2.4배만큼 빠르게 작업을 완료할 수 있었다. 이를 통해 비탈면 모델링을 보다 효율적으로 수행하고 모델링 파라미터 저장 기능을 통해 급작스러운 설계변경사항을 적용할 수 있을 뿐만 아니라, 향후 택지조성공사 BIM 도입의 활성화에 기여할 것으로 기대된다. Recently, interest in Building Information Modeling (BIM) has increased globally, and 3D modeling is a start for the application of BIM at construction sites. However, while many studies have been conducted on the efficiency of 3D modeling focused on civil facilities, there is a lack of research on the earthwork BIM. In particular, since 3D slope often has complex shapes depending on the ground models, the efficiency method for 3D slope are needed. This study analyzed the interfaces and procedures of other software to find out what functions users need. Then the functions to enter intervals between 3D faces, select multiple ground models, and improve the interface are reflected on the developed system and is able to efficiently perform modeling with only five steps, and reduce the number of clicks and inputs. As a result of conducting the test to verify the efficiency, using the developed system made skilled users complete modeling at least 1.8 times faster and unskilled people at least 2.4 times faster than using other software. This is expected to perform 3D slope modeling more efficiently, as well as to contribute to the activation of future BIM adoption for housing construction projects.
권용규,도경희,박성정,장민철,전민호 대한재활의학회 2015 Annals of Rehabilitation Medicine Vol.39 No.5
Objective To evaluate whether repetitive transcranial magnetic stimulation (rTMS) could improve dysarthria in stroke patients at the subacute stage.Methods This study was a prospective, randomized, double-blind controlled trial. Patients who had unilateral middle cerebral artery infarction were enrolled. In patients in the rTMS group, we found hot spots by searching for the evoked motor potential of the orbicularis oris on the non-affected side. We performed rTMS at a low frequency (1 Hz), 1,500 stimulations/day, 5 days a week for 2 weeks on the hotspots. We used the same protocol in the sham stimulation group patients as that in the rTMS group, except that the angle of the coil was perpendicular to the skull rather than tangential to it. The patients in both groups received speech therapy for 30 minutes, 5 days a week from a skilled speech therapist. The speech therapist measured the Urimal Test of Articulation and Phonology, alternative motion rates, sequential motion rates, and maximal phonation time before and after intervention sessions.Results Forty-two patients were enrolled in this study and 20 completed the study. Statistical analysis revealed significant improvements on the dysarthria scales in both groups. The sequential motion rate (SMR)-PəTəKə showed significantly greater improvement in the rTMS group patients than in the sham stimulation group.Conclusion Patients in the rTMS group showed greater improvement in articulation than did patients in the sham rTMS group. Therefore, rTMS can have a synergistic effect with speech therapy in treating dysarthria after stroke.
변동하중을 받는 Glass/Epoxy 복합재료의 피로수명 예측
권용규(Yong-Kyu Kwon),강기원(Ki-Weon Kang),김정규(Jung-Kyu Kim) 대한기계학회 2002 대한기계학회 춘추학술대회 Vol.2002 No.8
This paper presents the fatigue behavior of composite materials with impact-induced damage under constant amplitude and random loading. For this purpose, the fatigue tests under constant amplitude and random loading were performed on the impacted composite materials. The fatigue life of the impacted materials under the constant amplitude loading can be identified through the prediction model, based on the fatigue characteristics of virgin materials and residual strength due to impact damage. Also, the model for equivalent stress is proposed to estimated the fatigue life under random loading, based on the S-N curves under constant amplitude loading. The equivalent stress and corresponding fatigue life by the present model agrees well with the experimental results.